Abstract:In order to improve the data productivity of a wind tunnel test, the model under investigation in the wind tunnel is moved continuously with a predetermined constant angular speed in the so-called pitch–traverse mode. Alternatively, the wind tunnel model can be moved in the so-called pitch–pause mode, in which it keeps its position for a certain (measurement) time at a fixed pitch position, after which it is moved to the next pitch position. The latter procedure is more time-consuming, so, for the same time interval, the number of measured data points taken in the pitch–pause mode is less than that for the pitch–traverse mode. Since wind tunnel test time can be quite expensive, in most wind tunnel tests where only conventional forces and pressures are recorded with conventional measuring systems, the wind tunnel model is moved in the pitch–traverse mode in order to obtain as much aerodynamic data as possible during the tunnel runtime. The application of the Pressure-Sensitive Paint (PSP) technique has been widely used in wind tunnel testing for the purpose of providing pressure data on wind tunnel models with high spatial resolution. The lifetime-based PSP method has several advantages over the intensity-based method since it often has higher accuracy. Up until now, the lifetime-based PSP technique has mainly been used for wind tunnel testing, where the test model has been moved to the pitch–pause mode. The traditional lifetime method using on-chip accumulation requires multiple (~1000) excitation light pulses to accumulate enough luminescence (fluorescence or phosphorescence) photons on the camera sensor to provide acceptable signal-to-noise ratios and, therefore, it may seem to be not compatible with a continuously moving wind tunnel model. Nevertheless, the present study verifies the application of lifetime-based PSP utilizing on-chip accumulation with a continuously moving wind tunnel model which would make the entire PSP data acquisition compatible with that of the conventional measurements (forces and pressures), as mentioned above. In this paper, the applicability of the lifetime-based PSP technique to a continuously moving wind tunnel model (in pitch–traverse mode) is investigated with the help of measurements in the transonic wind tunnel in Göttingen (TWG). For this investigation, PSP was applied on the delta-wing model DLR-F22, which is to be tested in TWG. The pressure distribution on the wind tunnel model was measured using the PSP lifetime method for both model movement modes (pitch–pause and pitch–traverse mode) so that the corresponding PSP results could be directly compared with each other. In addition, an error analysis of the PSP results was carried out and compared with the conventional pressure measurement results, hence providing an assessment of the accuracy of the PSP results; finally, a recommendation for future PSP measurements could be given.

Pressure-Sensitive Paint Measurements in Narrow Clearances: A Feasibility Study

Pressure-sensitive paint measurements in a shock tube

Pressure-sensitive Paint with Imprinted Pattern for Full-Field Endoscopic Measurement Using a Color Camera

Temperature- and Pressure-Sensitive Paint Measurements in Short-Duration Hypersonic Flow

Study on Dynamic Pressure Detection Method for Flow Field Based on PVDF Film

A TEMPERATURE-GRADIENT CORRECTION METHOD FOR FILM COOLING EFFECTIVENESS MEASUREMENT USING ENDOSCOPE-BASED PSP TECHNIQUE

Experimental analysis of pressure deviation-induced film cooling effectiveness deviation in pressure sensitive paint measurement

Radial Displacement Measurement of Hydrogen Storage Cylinders under Internal Pressure Based on Fringe Projection Profilometry

Resolving dynamic features of kilohertz pressure fluctuations using fast-responding pressure-sensitive paint: measurement of inclined jet impingement

The Development and Application of Two-Color Pressure-Sensitive Paint in Jet Impingement Experiments

Fast pressure-sensitive paint measurements of dynamic stall on a pitching airfoil via intensity- and lifetime-based methods

Comparison of Lifetime-Based Pressure-Sensitive Paint Measurements in a Wind Tunnel Using Model Pitch–Traverse and Pitch–Pause Modes

Frequency Response of Pressure-Sensitive Paints under Low-Pressure Conditions

Unsteady Pressure-Sensitive-paint (PSP) Measurement in Low-Speed Flow: Characteristic Mode Decomposition and Noise Floor Analysis

Experimental Study of Shaped Hole Film Cooling Using Pressure Sensitive Paint

Pressure-sensitive paint measurements with temperature correction on the wing of AGARD-B under transonic flow conditions

Instrumentation of a Rolling Bearing with a Thin Film Piezo Coating for Oil Film Measurement

Indexes for Evaluation of Dynamic Characteristics of Pressure-Sensitive Paint based on Pressure Sensitivity and Frequency Response

Multi-position Measurement of Oil Film Thickness Within the Slipper Bearing in Axial Piston Pumps

Time-resolved pressure-sensitive paint measurements for cryogenic wind tunnel tests

Dual-luminophore fast-responding pressure-sensitive paint for the simultaneous elimination of motion- and temperature-induced errors