Abstract:In order to improve the data productivity of a wind tunnel test, the model under investigation in the wind tunnel is moved continuously with a predetermined constant angular speed in the so-called pitch–traverse mode. Alternatively, the wind tunnel model can be moved in the so-called pitch–pause mode, in which it keeps its position for a certain (measurement) time at a fixed pitch position, after which it is moved to the next pitch position. The latter procedure is more time-consuming, so, for the same time interval, the number of measured data points taken in the pitch–pause mode is less than that for the pitch–traverse mode. Since wind tunnel test time can be quite expensive, in most wind tunnel tests where only conventional forces and pressures are recorded with conventional measuring systems, the wind tunnel model is moved in the pitch–traverse mode in order to obtain as much aerodynamic data as possible during the tunnel runtime. The application of the Pressure-Sensitive Paint (PSP) technique has been widely used in wind tunnel testing for the purpose of providing pressure data on wind tunnel models with high spatial resolution. The lifetime-based PSP method has several advantages over the intensity-based method since it often has higher accuracy. Up until now, the lifetime-based PSP technique has mainly been used for wind tunnel testing, where the test model has been moved to the pitch–pause mode. The traditional lifetime method using on-chip accumulation requires multiple (~1000) excitation light pulses to accumulate enough luminescence (fluorescence or phosphorescence) photons on the camera sensor to provide acceptable signal-to-noise ratios and, therefore, it may seem to be not compatible with a continuously moving wind tunnel model. Nevertheless, the present study verifies the application of lifetime-based PSP utilizing on-chip accumulation with a continuously moving wind tunnel model which would make the entire PSP data acquisition compatible with that of the conventional measurements (forces and pressures), as mentioned above. In this paper, the applicability of the lifetime-based PSP technique to a continuously moving wind tunnel model (in pitch–traverse mode) is investigated with the help of measurements in the transonic wind tunnel in Göttingen (TWG). For this investigation, PSP was applied on the delta-wing model DLR-F22, which is to be tested in TWG. The pressure distribution on the wind tunnel model was measured using the PSP lifetime method for both model movement modes (pitch–pause and pitch–traverse mode) so that the corresponding PSP results could be directly compared with each other. In addition, an error analysis of the PSP results was carried out and compared with the conventional pressure measurement results, hence providing an assessment of the accuracy of the PSP results; finally, a recommendation for future PSP measurements could be given.

Pressure-sensitive paint measurements with temperature correction on the wing of AGARD-B under transonic flow conditions

Temperature- and Pressure-Sensitive Paint Measurements in Short-Duration Hypersonic Flow

A TEMPERATURE-GRADIENT CORRECTION METHOD FOR FILM COOLING EFFECTIVENESS MEASUREMENT USING ENDOSCOPE-BASED PSP TECHNIQUE

Pressure-sensitive paint measurements in a shock tube

A Two-Dimensional Temperature Correction Method for Pressure-Sensitive Paint Measurement on Helicopter Rotor Blades

Pressure Measurement on Suction Surface of a Single Vane Using Pressure-sensitive Paint

Time-resolved pressure-sensitive paint measurements for cryogenic wind tunnel tests

Correction Method for Film Cooling Effectiveness Measurement with Temperature Gradient Using Endoscopic PSP and TSP Technique

Fast pressure-sensitive paint measurements of dynamic stall on a pitching airfoil via intensity- and lifetime-based methods

Application of Optical Pressure Sensitive Paint Measurement Technique in Internal Flow Fields

Pressure field measurements on large-scale propeller blades using pressure-sensitive paint

Experimental analysis of pressure deviation-induced film cooling effectiveness deviation in pressure sensitive paint measurement

High Sensitive Flexible Hot-Film Sensor for Measurement of Unsteady Boundary Layer Flow

The Development and Application of Two-Color Pressure-Sensitive Paint in Jet Impingement Experiments

Application of the PSP Technique in Low Speed Wind Tunnels

Application Of Temperature-Sensitive Paint For Transition Detection On An NLF Forward-Swept Wing Under Harmonic Pitch Oscillation At Flight-Relevant Mach And Reynolds Numbers

Pressure-Sensitive-Paint-Driven Hybrid Unsteady Compressible Flow Simulation

Pressure-Sensitive Paint Measurements in Narrow Clearances: A Feasibility Study

Comparison of Lifetime-Based Pressure-Sensitive Paint Measurements in a Wind Tunnel Using Model Pitch–Traverse and Pitch–Pause Modes

PSP Experiment of Global Surface Pressure Distribution on Suction Surface of Compressor Cascade with Large Curved Angle

A Grid-Pattern PSP/TSP System for Simultaneous Pressure and Temperature Measurements