Abstract:There are many sand-laden waters in China, and the wear of hydraulic structures caused by sand-laden water diversion has been paid more and more attention. Taking the spillway of a reservoir as the research object, the numerical model of erosion wear caused by sediment-laden particle flows on the spillway was established by using the computational fluid dynamics (CFD) method, VOF (Volume of Fluid) multiphase flow model and DPM (Discrete Phase Model). Through the simulation analysis of the spillway’s overall erosion, the distribution of the spillway erosion wear was obtained. Then, according to the main wear parts, the single variable, such as sediment diameter, sediment concentration, flow velocity and gate opening degree, was changed to study the erosion amount of the spillway and the distribution law of the spillway erosion parts. The results show that the main erosion sites of the spillway are at the bottom of the gate chamber and the middle section of the spillway. The maximum erosion increases linearly with the increase in sediment concentration. With the increase in sediment concentration, the sediment concentration changed from 1 kg/m3 to 6 kg/m3, and the maximum erosion of the spillway increased from 2.58 × 10−7 kg/m2 to 1.53 × 10−6 kg/m2. The erosion at the bottom of the spillway and gate leaf increases first and then decreases with the increase in sediment diameter and reaches the maximum value when the particle size is 0.002 mm. The erosion at the bottom of the spillway and the gate leaf increases with different growth trends as the flow velocity increases, when the flow velocity increases from 2 m/s to 9 m/s and the maximum erosion amount at the bottom of the spillway increases from 3.66 × 10−7 kg/m2 to 1.14 × 10−6 kg/m2, and the maximum erosion of the gate leaf increased from 1.66 × 10−8 kg/m2 to 8.98 × 10−6 kg/m2. The erosion amount at the bottom of the spillway increases with the increase in the gate opening between 0 and 3 m and tends to be stable when the gate opening is greater than 3 m. The maximum erosion position moves to the rear part of the spillway with the change in the gate opening. The change in the gate opening has no obvious effect on the erosion amount of the gate leaf but only changes the area of the gate erosion part. Thus, the erosion wear distribution of spillway under different work conditions is summarized, and the qualitative study between the erosion wear and the distribution of sediment diameter, sediment concentration, flow velocity and gate opening degree is made.

Erosion behavior and influence of solid particles in hydraulic spool valve without notches

Visualization and Influence Factors of Erosion at the Working Edge of a Hydraulic Servo Spool Valve

Erosion microscopic morphology and formation mechanism of hydraulic servo spool valve

A prediction model of fluid-solid erosion wear in hydraulic spool valve orifice

The CFD Analysis of Cavitation Erosion and Structural Optimization for an Unloading Valve

Three-dimensional numerical investigation of solid particle erosion in gate valves

Experimental and Numerical Studies on Erosion Damage in Damping Holes on the Valve Plate of an Axial Piston Pump

An Optimized E/CRC Erosion Model of Round Particles for Hydraulic Spool Valves With Euler–Lagrange Two-Phase Simulation

Numerical Investigation of Erosion Wear in the Hydraulic Amplifier of the Deflector Jet Servo Valve

Steady Flow Torques in a Servo Motor Operated Rotary Directional Control Valve

Friction and Lubrication Behavior of a Selective Laser Melted Hydraulic Spool Valve under Contaminated Conditions

CFD-Based Physical Failure Modeling of Direct-Drive Electro-Hydraulic Servo Valve Spool and Sleeve

Numerical Investigation of Cavitation Flow Inside Spool Valve with Large Pressure Drop

The Influence of Governing Valve Opening on the Erosion Characteristics of Solid Particle in Steam Turbine

Numerical Investigation of Erosion Wear Characteristics of Hydraulic Spillway

Research on the Erosion Resistance of High-Pressure Liquid–Solid Two-Phase Flow Junction Drilling Spool

Numerical Study On Temperature Field And Spool Deformation Of Throttle Slide Valve With V-Notches

Unbalanced Force Analysis on Valve Core Clamping in Hydraulic Spool Valves

Reduction of Steady Flow Torques in a Single-Stage Rotary Servo Valve

Solid-liquid Flow Characteristics and Sticking-Force Analysis of Valve-Core Fitting Clearance

Numerical Study on Sealing Performance after Wear of Plug Valve During Opening–closing Process