Abstract:Hydraulic spool valves may clamp under the action of sensitive particles when working in hydraulic oils that contain solid particles, which will then bring about a devastating detriment to the machines. According to the failure statistics of hydraulic systems organized by ISO, more than 80% of the operational failures of hydraulic systems are caused by fluid contamination, and particulate contamination is the most important factor causing spool valve stagnation. In this paper, we considered various factors, including the material, size, and concentration of particles and the spool postures, and built a systematic spool clamping mechanical model. A device was designed to measure the spool valve friction under the action of particles. The influence of particle material, concentration, and size on the friction force of spool valves was investigated. By experiments, we measured the spool clamping force under the action of each single factor and then fitted the datum quantity of spool clamping force and the empirical equation of pulsating quantity. The study results demonstrate three types of non-ideal postures of spools in a valve hole, which are off-center, tilting, and off-center with tilting. Those three postures can engender clamping risk zones with different ranges inside the clearance between spool valves, increasing the risk of spool clamping. The kind of particles is found to have a certain but limited impact on the spool clamping force. Usually, particles with a higher elastic modulus can trigger a larger spool clamping force, which is in line with the theoretical equation. Within a certain range, the probability density distribution of particle size tallies with the normal distribution function, where the “sensitive particles” take up 0.7–1 of the clearance between spool valves. A higher particle volume fraction in oils means a greater number of sensitive particles and a larger spool clamping force. For the particles of a similar size with the clearance between spool valves, when their volume concentration tops over the “sensitive concentration”, namely 5%, the risk of spool clamping rises in a drastic manner. This study provides a theoretical reference and an empirical equation for the mechanism of spool clamping under the action of particles, as well as a definite quantitative indicator for the prediction and estimation of spool clamping which is of positive significance for the study of the predictive maintenance of hydraulic equipment.

Solid-liquid Flow Characteristics and Sticking-Force Analysis of Valve-Core Fitting Clearance

Visualization and Influence Factors of Erosion at the Working Edge of a Hydraulic Servo Spool Valve

Analysis of force and leakage in water hydraulic motor' s piston pairs

Research on Fluid Dynamics and Thermal Characteristics in Hydraulic Valves by Thermal-Fluid-Solid Coupling Method

Unbalanced Force Analysis on Valve Core Clamping in Hydraulic Spool Valves

Numerical Investigation of Micrometer-Sensitive Particle Intrusion in Hydraulic Valve Clearances and Its Impact on Valve Performance

Flow Dynamic Analysis Inside a Sleeve Regulating Valve with Different Valve Core Shapes

Three-dimensional numerical investigation of solid particle erosion in gate valves

Experimental and Modeling Investigation on Dynamic Response of Sticky Control Valves

Numerical Simulation of the Gas-Solid Flow Around the Valve of Pneumatic Conveying System

Experimental and Numerical Analysis of Spring Stiffness on Flow and Valve Core Movement in Pilot Control Globe Valve

Friction and Lubrication Behavior of a Selective Laser Melted Hydraulic Spool Valve under Contaminated Conditions

Flow Force Analysis and Structural Optimization of a Large Flow Rate Pressure Compensation Valve

Fluid Dynamics Investigation on the Body Structure Inside a Sleeve Regulating Valve

Computational fluid dynamics analysis on orifice structure inside valve core of pilot-control angle globe valve

Fluid-structure interaction analysis on vibration characteristics of sleeve control valve

Numerical and Experimental Investigation on Opening Direction Steady Axial Flow Force Compensation of Converged Flow Cartridge Proportional Valve

Characterization of Hydraulic Spool Clamping Triggered by Solid Particles Based on Mechanical Model and Experiment Research

Structure improvement and parameter optimization of micro flow control valve

Flow Force Regulation of the Main Poppet in a Large Flow Load Control Valve

Numerical Analysis of Flow and Cavitation Characteristics in a Pilot-Control Globe Valve with Different Valve Core Displacements