Abstract:There are many sand-laden waters in China, and the wear of hydraulic structures caused by sand-laden water diversion has been paid more and more attention. Taking the spillway of a reservoir as the research object, the numerical model of erosion wear caused by sediment-laden particle flows on the spillway was established by using the computational fluid dynamics (CFD) method, VOF (Volume of Fluid) multiphase flow model and DPM (Discrete Phase Model). Through the simulation analysis of the spillway’s overall erosion, the distribution of the spillway erosion wear was obtained. Then, according to the main wear parts, the single variable, such as sediment diameter, sediment concentration, flow velocity and gate opening degree, was changed to study the erosion amount of the spillway and the distribution law of the spillway erosion parts. The results show that the main erosion sites of the spillway are at the bottom of the gate chamber and the middle section of the spillway. The maximum erosion increases linearly with the increase in sediment concentration. With the increase in sediment concentration, the sediment concentration changed from 1 kg/m3 to 6 kg/m3, and the maximum erosion of the spillway increased from 2.58 × 10−7 kg/m2 to 1.53 × 10−6 kg/m2. The erosion at the bottom of the spillway and gate leaf increases first and then decreases with the increase in sediment diameter and reaches the maximum value when the particle size is 0.002 mm. The erosion at the bottom of the spillway and the gate leaf increases with different growth trends as the flow velocity increases, when the flow velocity increases from 2 m/s to 9 m/s and the maximum erosion amount at the bottom of the spillway increases from 3.66 × 10−7 kg/m2 to 1.14 × 10−6 kg/m2, and the maximum erosion of the gate leaf increased from 1.66 × 10−8 kg/m2 to 8.98 × 10−6 kg/m2. The erosion amount at the bottom of the spillway increases with the increase in the gate opening between 0 and 3 m and tends to be stable when the gate opening is greater than 3 m. The maximum erosion position moves to the rear part of the spillway with the change in the gate opening. The change in the gate opening has no obvious effect on the erosion amount of the gate leaf but only changes the area of the gate erosion part. Thus, the erosion wear distribution of spillway under different work conditions is summarized, and the qualitative study between the erosion wear and the distribution of sediment diameter, sediment concentration, flow velocity and gate opening degree is made.

An Optimized E/CRC Erosion Model of Round Particles for Hydraulic Spool Valves With Euler–Lagrange Two-Phase Simulation

Visualization and Influence Factors of Erosion at the Working Edge of a Hydraulic Servo Spool Valve

The CFD Analysis of Cavitation Erosion and Structural Optimization for an Unloading Valve

Coarse-grained CFD-DEM Simulation of Elbow Erosion Induced by Dilute Gas-Solid Flow: A Multi-Level Study

Erosion behavior and influence of solid particles in hydraulic spool valve without notches

Numerical simulation research for the effect of particle shape on the erosion wear in elbow

Three-dimensional numerical investigation of solid particle erosion in gate valves

Research on the Erosion Resistance of High-Pressure Liquid–Solid Two-Phase Flow Junction Drilling Spool

A prediction model of fluid-solid erosion wear in hydraulic spool valve orifice

Erosion microscopic morphology and formation mechanism of hydraulic servo spool valve

Experimental and Numerical Studies on Erosion Damage in Damping Holes on the Valve Plate of an Axial Piston Pump

Numerical Investigation of Erosion Wear in the Hydraulic Amplifier of the Deflector Jet Servo Valve

An Improved Eulerian-Lagrangian Method Combined with Ductile Material Model for Cavitation Erosion Assessment

Eulerian-Lagrangian investigation of erosion wear within a water-submerged Jet: Two-way coupling

An improved model for predicting the erosion within the DEM framework

Numerical Prediction of Solid Particle Erosion in Jet Pumps Based on a Calibrated Model

Multi-objective Optimization of Surface Texture for the Slipper/swash Plate Interface in EHA Pumps

Silt abrasion prediction of hydraulic machine components by two-fluid model

Numerical Investigation of Erosion Wear Characteristics of Hydraulic Spillway

Unbalanced Force Analysis on Valve Core Clamping in Hydraulic Spool Valves

Erosion Characteristics and Flashing Flow of High-differential-pressure Control Valves: A Numerical Study using an Erosion-Coupled Dynamic Mesh