Abstract:The paper substantiates the composition and prospects of using high strength Al–Zn–Mg–Ca–Fe casting aluminum alloy without heat treatment based on the study on the structure, technological and mechanical properties. Alloys of the base composition Al–5.5%Zn–1.5%Mg (wt.%) jointly and separately doped with 0.5–1.0 % Ca and 0.5 % Fe were obtained as the objects of research. Standard casting alloys according to GOST 1583-93: AK12M2, AMg6lch, AM4,5Kd were the objects of comparison. A hot tensile test using a cast test bar was conducted to check the tendency to form hot cracks due to hindered contraction. It was shown that separate alloying with calcium and iron does not contribute to the improvement of crack resistance and adversely affects mechanical properties. Combined alloying with 1 % Ca and 0.5 % Fe improves the hot tearing resistance to the level of the AMg6lch alloy properties. This effect is due to calcium-containing phases of eutectic origin formed and a favorable grain structure created that is free from columnar grains. Iron in the alloy structure is bound in compact Al 10 CaFe 2 phase particles as a result of the non-equilibrium crystallization during permanent mold casting. The formation of this phase allowed to reduce the amount of zinc in the (Al, Zn) 4 Ca phase and mostly retain the (Al) solid solution composition as evidenced by similar hardness values of the Al–5.5%Zn–1.5%Mg base alloy and Al–5.5%Zn–1.5%Mg–1%Ca–0.5%Fe alloy, and the superiority of the values over the hardness of alloys separately alloyed with calcium and iron. Also the cast hardness of the promising alloy more than 20 HV higher than the cast hardness of commercial cast alloys. The new alloy in the as-cast condition exhibited competitive mechanical tensile properties: UTS ~ 310 MPa, YS ~ 210 MPa, El ~ 4 %.

Design of Mg Zn Si Ca casting magnesium alloy with high thermal conductivity

A high performance Mg-Al-Ca alloy processed by high pressure die casting: Microstructure, mechanical properties and thermal conductivity

Advanced wrought Mg-4.5Al-2.5Ca-0.02Mn (at%) alloys with exceptional balance of high thermal conductivity, yield strength, ductility, nonflammability, and corrosion resistance

Recent advancements in thermal conductivity of magnesium alloys

A high pressure die cast magnesium alloy with superior thermal conductivity and high strength

Effect of Zn content on microstructure, mechanical properties and thermal conductivity of extruded Mg-Zn-Ca-Mn alloys

Development of Mg–Zn–Mn–Y magnesium alloy with high thermal conductivity and compression properties via injection molding

Microstructure, Mechanical and Thermal Properties of Mg-0.5Ca-xZr Alloys

Utilizing Low Solubility, Light Metal Eutectic Systems for Castable, High Electrical/Thermal Conductivity Alloys

Effect of Thickness on the Thermal Conductivity and Microstructure of Die-Cast AZ91D Magnesium Alloy

Thermal Characteristics of Mg–Zn–Mn Alloys with High Specific Strength and High Thermal Conductivity

Cast magnesium alloys for elevated temperature applications

High Strength-Thermal Conductivity Mg–Ga–Ca–Ce Sheet by Hot-Extrusion and Rolling

Thermal Conductivity of AlSi10MnMg Alloy in Relation to Casting Technology and Heat Treatment Method

Thermal properties of AZ series cast Magnesium alloys

Effect of Mg content on mechanical properties and electrical conductivity of ultrafine-grained Al–Mg–Zr wires produced by ECAP-Conform and drawing

New high-strength casting aluminum alloy based on the Al–Zn–Mg–Ca–Fe system without requirement for heat treatment

Improving thermal conductivity of Mg-Si-Zn-Cu alloy through minimizing electron scattering at phase interface

Thermal and electrical conductivity of binary magnesium alloys

Simultaneous Enhancement of Thermal Conductivity and Mechanical Properties of EZ42 Magnesium Alloy by Ca Microalloying

High Strength Extruded Mg–5Zn–2Nd–1.5Y–0.6Zr–0.4Ca Alloy Produced by Electromagnetic Casting