Abstract:Mg-9.5Gd-4Y-2Zn-0.3Zr alloy wires with a diameter of 1.2 mm were fabricated by a multistage drawing process with a cumulative area reduction (CAR) of 96% at 500 °C using as-extruded rods with a diameter of 6 mm as the raw material. Investigated the impact of microstructural transformations on the mechanical performance of these wires, with a focus on phase evolution, texture changes, and grain refinement. In the alloy, second-phase 18R-LPSO, rare-earth-rich (RE-rich) phase, and Zn2Zr3 distributed at the grain boundaries along the extrusion direction (ED) or the drawing direction (DD), which were different from the intragranular 14H-LPSO phase, were observed. Significantly, we observed the transformation of blocky 18R-LPSO phases into sub-2μm W-Mg3Zn3RE2 particles during hot drawing. All the as-extruded and as-drawn wires exhibited equiaxed grains with average sizes between 4 μm and 7 μm. The as-extruded wires exhibited a texture with {0001} perpendicular to ED. As the CAR increased, the texture of the wires transformed into a basal texture with {0001} parallel to DD. The ultimate tensile strength (UTS) and tensile yield strength (TYS), respectively, increased from 369 MPa to 283 MPa for the as-extruded wire to 466 MPa and 436 MPa for the as-drawn wire with CAR increasing to 55%, and then decreased to 328 MPa and 318 MPa for the wire with CAR increasing to 96%. The elongation (EL) reduced from 8.01% to 1.37% with CAR increasing to 96%. As CAR exceeded 55%, the increased volume fraction of the W-Mg3Zn3RE2 phase resulted in a significant decrease in both the strength and the plasticity of the wires. The evolution of microstructure and mechanical properties provides possibility for regulating both the strength and elongation of the Mg-Gd-Y-Zn-Zr alloy wires by optimizing the drawing process.

Effect of Mg content on mechanical properties and electrical conductivity of ultrafine-grained Al–Mg–Zr wires produced by ECAP-Conform and drawing

Phase transformation, texture evolution, and mechanical properties of Mg-9.5Gd-4Y-2Zn-0.3Zr alloy wires fabricated using hot drawing

Effects of Zr and Mg alloying on microstructure and properties of Cu-Cr-Si alloys

Effect of Grain Boundary Segregation on Microstructure and Mechanical Properties of Ultra-Fine Grained Mg–Al–Ca–Mn Alloy Wires

Structure and Properties of Ca and Zr Containing Heat Resistant Wire Aluminum Alloy Manufactured by Electromagnetic Casting

Effect of Zn content on microstructure, mechanical properties and thermal conductivity of extruded Mg-Zn-Ca-Mn alloys

Microstructure evolution and mechanical property of Mg-Gd-Y-Zn-Zr alloy wires prepared by hot drawing

Effect of Zr addition on properties of Al–Mg–Si aluminum alloy used for all aluminum alloy conductor

Effect of Zn Concentration on the Microstructures and Mechanical Properties of Extruded Mg–7Y–4Gd–0.4Zr Alloys

Achieving excellent strength-ductility combination of Al-aided Mg-Gd-Al-Zr-Zn alloys fabricated by cold metal transfer-based wire-arc directed energy deposition via uniform equiaxed grains and multiple precipitates

Microstructure and Thermal Conductivity of Mg-2Zn-Zr Alloy

Effect of heat treatment on the microstructure and mechanical properties of Mg-Gd-Y-Zr alloys fabricated by wire arc additive manufacturing

Revealing precipitation behavior and mechanical response of wire-arc directed energy deposited Mg-Gd-Y-Zr alloy by tailoring aging procedures

Enhanced Strength‐Ductility Synergy of Mg‐6Zn Alloy Wire by Inducing GP Zone Precipitation

Mechanical Properties and Microstructures of Mg-Al-Zn Alloys with High Aluminum Contents

Microstructure, Mechanical and Thermal Properties of Mg-0.5Ca-xZr Alloys

Microstructure and Hot Deformation Behaviour of Twin-Roll Cast AZ31 Magnesium Wire

Enhanced Mechanical Properties in Fine-Grained Mg–1.0Zn–0.5Ca Alloys Prepared by Extrusion at Different Temperatures

Microstructure and Mechanical Properties of Extruded Mg-Zn-Y Alloy

Enhancement of Strength and Electrical Conductivity for a Dilute Al-Sc-Zr Alloy Via Heat Treatments and Cold Drawing