Abstract:The insufficient ionic conductivity of oxide-based solid electrolytes and the large interfacial resistance between the cathode material and the solid electrolyte severely limit the performance of room-temperature all-solid-state sodium rechargeable batteries. A NASICON solid electrolyte Na3.4Zr1.9Zn0.1Si2.2P0.8O12, with superior room-temperature conductivity of 5.27 × 10–3 S cm–1, is achieved by simultaneous substitution of Zr4+ by aliovalent Zn2+ and P5+ by Si4+ in Na3Zr2Si2PO12. The bulk conductivity and grain boundary conductivity of Na3.4Zr1.9Zn0.1Si2.2P0.8O12 are nearly 20 times and almost 50 times greater than those of pristine Na3Zr2Si2PO12, respectively. The FeS2||polydopamine-Na3.4Zr1.9Zn0.1Si2.2P0.8O12||Na all-solid-state sodium batteries, with a polydopamine modification thin layer between the solid electrolyte and the cathode, maintain a high reversible capacity of 236.5 mAh g–1 at a 0.1 C rate for 100 cycles and a capacity of 133.1 mAh g–1 at 0.5 C for 300 cycles, demonstrating high performance for all-solid-state sodium batteries.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsenergylett.0c01432?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsenergylett.0c01432</a>.Experimental section; XRD, NPD, SEM, and EIS measurements for different solid electrolyte materials; STEM-EDS and DC polarization measurement for Zn0.1 sample; EDS measurement for Zn0.1 sample before and after contact with sodium; unit cell parameters of different solid electrolyte materials; structural parameters of different solid electrolyte materials; BVEL analysis and the comparison of bottleneck sizes; conductivities, activation energies, and relative densities of different solid electrolyte materials; FTIR measurement for Zn0.1 pellet with and without PDA layer; charge–discharge curves of FeS2||Zn0.1||Na all-solid-state battery; comparison of conductivities and battery performances reported in the literature and in this work; cross-sectional images of the cathode/electrolyte interface before and after cycling (<a class="ext-link" href="/doi/suppl/10.1021/acsenergylett.0c01432/suppl_file/nz0c01432_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Enhanced electrochemical performance of all-solid-state sodium-sulfur batteries by PEO-NaCF3SO3-MIL-53(Al) solid electrolyte

High‐Capacity All‐Solid‐State Sodium Metal Battery with Hybrid Polymer Electrolytes

Robust Polymer Electrolyte with Enhanced Ionic Conductivity Realized by the Incorporation of Electrospun MgAl 2 O 4 Nanofibers

Hot‐Pressing Enhances Mechanical Strength of PEO Solid Polymer Electrolyte for All‐Solid‐State Sodium Metal Batteries

Ultrastable All-Solid-State Sodium Rechargeable Batteries

S/MWCNt/LLZO composite electrode with e−/S/Li+ conductive network for all-solid -state Lithium–Sulfur batteries

Novel PEO-based composite solid electrolytes for all-solid-state Li-S battery

High Capacity And Superior Cyclic Performances Of All-Solid-State Lithium-Sulfur Batteries Enabled By A High-Conductivity Li10snp2s12 Solid Electrolyte

Enabling high-performance all-solid-state lithium batteries with high ionic conductive sulfide-based composite solid electrolyte and ex-situ artificial SEI film

High-Performance All-Solid-State Li-S Batteries Enabled by Reaction Kinetics Enhancement and Interface Stabilization

Cathode-Supported-Electrolyte Configuration for High-Performance All-Solid-State Lithium–Sulfur Batteries

A High-Capacity Polyethylene Oxide-Based All-Solid-State Battery Using a Metal–Organic Framework Hosted Silicon Anode

High-Performance All-Inorganic Solid-State Sodium-Sulfur Battery.

Ultrathin, Flexible Polymer Electrolyte for Cost‐Effective Fabrication of All‐Solid‐State Lithium Metal Batteries

Super Long‐Cycling All‐Solid‐State Battery with Thin Li6PS5Cl‐Based Electrolyte

Tailoring Electrolyte Distributions to Enable High‐performance Li <sub>3</sub> PS <sub>4</sub> ‐based All‐solid‐state Batteries under Different Operating Temperatures

Nanostructured zeolitic imidazolate framework-67 reinforced poly(ethylene oxide) composite electrolytes for all solid state Lithium ion batteries

Stable Seamless Interfaces and Rapid Ionic Conductivity of Ca–CeO2/LiTFSI/PEO Composite Electrolyte for High‐Rate and High‐Voltage All‐Solid‐State Battery

3D interconnected MOF-derived asymmetric bilayer solid-state electrolyte for enabling homogeneous Li deposition of all-solid-state lithium metal batteries

Flexible Electrolyte and Cathode Membranes for All-Solid-State Batteries Fabricated by a One-Step Solvent Method

Flexible hybrid solid electrolyte incorporating ligament-shaped Li6.25Al0.25La3Zr2O12 filler for all-solid-state lithium-metal batteries