Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Cathode-Supported-Electrolyte Configuration for High-Performance All-Solid-State Lithium–Sulfur Batteries

Exploring the Concordant Solid-State Electrolytes for All-Solid-state Lithium-Sulfur Batteries

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

Rational Designed Mixed-Conductive Sulfur Cathodes for All-Solid-State Lithium Batteries

Nano‐Scale Interface Engineering of Sulfur Cathode to Enable High‐Performance All‐Solid‐State Li–S Batteries

Confining Sulfur in Porous Carbon by Vapor Deposition to Achieve High-Performance Cathode for All-Solid-State Lithium–Sulfur Batteries

Tailoring the Interface between Sulfur and Sulfide Solid Electrolyte for High-Areal-Capacity All-Solid-State Lithium–Sulfur Batteries

A highly utilized and practical lithium-sulfur cathode enabled in all-solid-state batteries

High-Performance All-Solid-State Lithium–Sulfur Batteries Enabled by Slurry-Coated Li6PS5Cl/S/C Composite Electrodes

Solid‐State Lithium–Sulfur Battery Enabled by Thio‐LiSICON/Polymer Composite Electrolyte and Sulfurized Polyacrylonitrile Cathode

Localized S-Li2s Conversion with Accelerated Kinetics Mediated by Mixed Conductive Shell for High-Performance Solid-State Lithium-Sulfur Battery

High-Performance All-Solid-State Lithium-Sulfur Battery Enabled by A Mixed-Conductive Li2s Nanocomposite

Improved lithium-ion and electrically conductive sulfur cathode for all-solid-state lithium–sulfur batteries

Integrated Structure of Cathode and Double-Layer Electrolyte for Highly Stable and Dendrite-Free All-Solid-State Li-Metal Batteries

High‐Performance All‐Solid‐State Lithium–Sulfur Batteries Enabled by Amorphous Sulfur‐Coated Reduced Graphene Oxide Cathodes

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

High-Performance Cathodes Prepared Via Liquid-Phase Method and Catalyzed by Co9S8 for All-Solid-State Lithium-Sulfur Batteries

High Performance Solid-State Lithium-Sulfur Battery Enabled by Multi-Functional Cathode and Flexible Hybrid Solid Electrolyte

Designing Cation–Solvent Fully Coordinated Electrolyte for High‐Energy‐Density Lithium–Sulfur Full Cell Based on Solid–Solid Conversion

Sandwich structured NASICON-type electrolyte matched with sulfurized polyacrylonitrile cathode for high performance solid-state lithium-sulfur batteries

Enabling high-performance all-solid-state lithium batteries with high ionic conductive sulfide-based composite solid electrolyte and ex-situ artificial SEI film