Abstract:The abundance of low-temperature waste heat produced by industry and automobile exhaust necessitates the development of power generation with thermoelectric (TE) materials. Commercially available bismuth telluride-based alloys are generally used near room temperature. Materials that are composed of p-type bismuth telluride, which are suitable for low-temperature power generation (near 380 K), were successfully obtained through Sb-alloying, which suppresses detrimental intrinsic conduction at elevated temperatures by increasing hole concentrations and material band gaps. Furthermore, hot deformation (HD)-induced multi-scale microstructures were successfully realized in the high-performance p-type TE materials. Enhanced textures and donor-like effects all contributed to improved electrical transport properties. Multiple phonon scattering centers, including local nanostructures induced by dynamic recrystallization and high-density lattice defects, significantly reduced the lattice thermal conductivity. These combined effects resulted in observable improvement of ZT over the entire temperature range, with all TE parameters measured along the in-plane direction. The maximum ZT of 1.3 for the hot-deformed Bi0.3Sb1.7Te3 alloy was reached at 380 K, whereas the average ZTav of 1.18 was found in the range of 300–480 K, indicating potential for application in low-temperature TE power generation. Thermoelectric materials, which convert temperature differences and electric voltage into each other, serve in refrigeration or power generation applications. Currently, bismuth telluride (Bi2Te3) and its alloys are the most widely used thermoelectric materials. Tie-Jun Zhu, Xin-Bing Zhao and co-workers from Zhejiang University, China, have now investigated the effect of antimony (Sb) alloying on bismuth tellurides through a series of polycrystalline solid solutions of Bi2-xSbxTe3—where x varies between 1.4 and 1.8—prepared by hot deformation. Systematic tuning of the alloy composition showed that higher antimony content raised the material's optimal conversion temperature by repressing undesirable conduction. This effect arises from an increase in both the hole concentration and the band gap in the material. For a composition where x is 1.7, the alloy showed optimal performances at 380 kelvin—a suitable temperature for low-temperature power generation from the waste heat generated by industry or vehicles. The p-type bismuth telluride-based polycrystalline materials suiting for low-temperature power generations (near 380 K) have been obtained through Sb-alloying and HD, which suppresses the detrimental effect of intrinsic conduction at elevated temperature via increasing the hole concentration and band gap. The hot-deformed Bi0.3Sb1.7Te3 alloy, not usual composition Bi0.5Sb1.5Te3, shows a maximum ZT of 1.3 at 380 K, indicating a bright application potential in low-temperature power generations.

Bismuth telluride (Bi2Te3) thermoelectric material as a transducer for solar energy application

Bismuth Telluride Based Efficient Thermoelectric Power Generator with Electrically Conducive Interfaces for Harvesting Low Temperature Heat

High Efficiency Bi2te3-Based Materials and Devices for Thermoelectric Power Generation Between 100 and 300 Degrees C

High efficiency Bi2Te3-based materials and devices for thermoelectric power generation between 100 and 300 °C

The Thermoelectric Properties of Bismuth Telluride

Recent advances of electrodeposition of Bi2Te3 and its thermoelectric applications in miniaturized power generation and cooling

BiSbTe alloy with high thermoelectric and mechanical performance for power generation

High Performance Dual-mode Module for Power Generation and Cooling Based on Optimized BiSbTe

A review on bismuth telluride (Bi2Te3) nanostructure for thermoelectric applications

Thermoelectric response of textured Sb2Te3–BiSb and Sb2Te3–Bi2Te3 thin film junctions

Enhanced thermoelectric performance at elevated temperature via suppression of intrinsic excitation in p-type Bi0.5−xSnxSb1.5Te3 thermoelectric material

Design of Bi2Te3-based thermoelectric generator in a widely applicable system

High Performance BiSbTe Alloy for Superior Thermoelectric Cooling

High Thermoelectric Performance Bismuth Telluride Prepared by Cold Pressing and Annealing Facilitating Large Scale Application

High‐Performance Industrial‐Grade p‐Type (Bi,Sb)2Te3 Thermoelectric Enabled by a Stepwise Optimization Strategy

Shifting Up the Optimum Figure of Merit of P-Type Bismuth Telluride-Based Thermoelectric Materials for Power Generation by Suppressing Intrinsic Conduction

Optimized Thermoelectric Properties of Bi0.48Sb1.52Te3 Through AgCuTe Doping for Low-Grade Heat Harvesting.

Bi2Te3-Based Thermoelectric Modules for Efficient and Reliable Low-Grade Heat Recovery

Achieving High Thermoelectric Performance in Bi2(Te, Se)3 Thin Film with (00 l)-Oriented by Incorporating Tellurization and Selenization Processes

Study and Characterization of Thermoelectric Material (TE) Bismuth Antimony Telluride

High-Temperature Thermoelectric Monolayer Bi2TeSe2 with High Power Factor and Ultralow Thermal Conductivity