Abstract:To have a better understand of film cooling technique, many experiments to investigate parameters affecting the film cooling effectiveness and heat transfer have been conducted. In this kind of experiments, different sorts of coolant (CO2, N-2 and etc.) are often applied to match coolant-to-mainstream properties or use some measuring techniques. However, the application of those coolant probably leads to a similarity problem, as the properties of them are different from air coolant in real engine conditions. This study investigates the accuracy of six criteria for the film cooling effectiveness scaling which changes the coolant from air to CO2 based on both experimental and numerical method, to promote the similarity to air coolant of film cooling experiments using CO2 as coolant. The study conducted on the pressure side of 1st stage stator from E-3 aero engine. The mainstream inlet pressure and temperature of the experiment was 112kPa and 312K, respectively. Numerical simulations were conducted by solving the Reynolds Averaged Naiver-Stokes (RANS) equations and Re-Normalization Group (RNG) k-epsilon turbulence model. The effect of CO2 coolant on pressure side film cooling effectiveness was initially investigated, followed by the analysis of the accuracy for six scaling criteria. Finally, reasons leading to the deviation of scaling was studied. Both numerical and experimental results indicate that the application of CO2 coolant leads to an obvious reduction of eta(APS) at relatively low coolant mass flow rate. That effect almost disappears at high coolant mass flow rate. In the experiment, eta with the variation in VR has the highest Pearson correlation coefficient (R-p) between air and CO2 coolant at almost all measuring points on pressure side, illustrating VR criterion has the highest accuracy in the scaling which the coolant is changed from air to CO2. The cooling effectiveness deviation of VR criterion is lower than 3% at all coolant CO2 percentage(obtained from CFD results). The low specific heat capacity of CO2 will lead to a relatively faster decay of injection temperature compared with air, producing an adverse influence on cooling effectiveness. The high density of CO2 can increase attachment ability of injections(especially on mid-span of the blade) and form a similar cooling film state to the air coolant at higher coolant mass flow rate. The results of this study can be used to promote the accuracy of the experiment using CO2 as coolant at relatively low temperature conditions in terms of film cooling effectiveness and injection state(attachment or separation). (c) 2021 Elsevier Ltd. All rights reserved.

Numerical Analysis of the Cooling System Performance and Effectiveness in Aluminum Low-Pressure Die Casting

Die Structure Optimization of Aluminum Alloy Wheel Low-Pressure Die Casting Based on CAE

Process Optimization of Low-pressure Die Casting of Aluminum Alloy Wheel based on Taguchi Method

Numerical auxiliary study of charge-air cooler design

Study of Flow and Heat Transfer in High Pressure Die Casting Cooling Channel

The Numerical Simulation about Second Dendrite Spacing of Low Pressure Casting Automobile Aluminum Magnesium Alloy Wheel

Effect of Cooling Process on Porosity in the Aluminum Alloy Automotive Wheel During Low-Pressure Die Casting

Numerical Simulation of Low Pressure Die Casting of Magnesium Wheel

Numerical Study on the Low Pressure Die Casting of AZ91D Wheel Hub

Numerical Simulation and Process Development for Low Pressure Diecasting of Magnesium Alloy Wheels

Numerical simulation of melt flow and temperature field during DC casting 2024 aluminium alloy under different casting conditions

Heat Transfer Coefficient Determination in a Gravity Die Casting Process with Local Air Gap Formation and Contact Pressure Using Experimental Evaluation and Numerical Simulation

Numerical Studies of Flow-Induced Defects in Aluminum Ingot Die Casting Process

Study on Cooling Channel Arrangement of High-Pressure Casting Die for Box-Like Workpieces

Accurate Simulation of Complex Temperature Field in Counter-Pressure Casting Process Using A356 Aluminum Alloy

Numerical Methods to Improve the Computational Efficiency of Thermal Analysis for the Die Casting Process

Numerical Simulation of the Pressure Casting Process for Magnesium Alloy Steering Wheel

Numerical and Experimental Study of Scaling Criteria Accuracy for Film Cooling Using CO2 Coolant

Multi-Objective Optimization of The Low-Pressure Casting of Large-Size Aluminum Alloy Wheels through a Systematic Optimization Idea

Numerical Investigation of Effects of Compound Angle and Length to Diameter Ratio on Adiabatic Film Cooling Effectiveness

Numerical Investigations Of Cooling Enhancement With Internal Ribs And External Coolant Film