Abstract:Purpose Temperature is a critical factor in the fused filament fabrication (FFF) process, which affects the flow behavior and adhesion of the melted filament and the mechanical properties of the final object. Therefore, modeling and predicting temperature in FFF is crucial for achieving high-quality prints, repeatability, process control and failure prediction. This study aims to investigate the melt deposition and temperature profile in FFF both numerically and experimentally using different Acrylonitrile Butadiene Styrene single-strand specimens. The process parameters, including layer thickness, nozzle temperature and build platform temperature, were varied. Design/methodology/approach COMSOL Multiphysics software was used to perform numerical simulations of fluid flow and heat transfer for the printed strands. The polymer melt/air interface was tracked using the coupling of continuity equation, equation of motion and the level set equation, and the heat transfer equation was used to simulate the temperature distribution in the deposited strand. Findings The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an infrared (IR) thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the three-dimensional (3D) printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand. Originality/value The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an IR thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the 3D printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand.

Heat Transfer and Adhesion Study for the FFF Additive Manufacturing Process

Finite Difference Modeling and Experimental Investigation of Cyclic Thermal Heating in the Fused Filament Fabrication Process

Experimental and numerical investigations on heat transfer in fused filament fabrication 3D-printed specimens

In-Situ Temperature Monitoring of ABS During Fused Filament Fabrication (FFF) Process With Varying Process Parameters

Interfacial Bonding During Multi-Material Fused Deposition Modeling (FDM) Process Due to Inter-Molecular Diffusion

Thermal analysis of fused deposition modeling process based finite element method: Simulation and parametric study

Efficient simulation of the heat transfer in fused filament fabrication

A High-Fidelity Thermal Model for a Novel Droplet-Based Additive Manufacturing Process for Polymers

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Insights into Temperature Simulation and Validation of Fused Deposition Modeling Processes

SENSING IN-SITU TEMPERATURES BY COORDINATES IN FUSED FILAMENT FABRICATION FOR IDENTIFYING INTERLAYER ANISOTROPIC MECHANICAL PROPERTIES AND ENABLING POST-FEM ANALYSIS

Radiative Thermal Effects in Large Scale Additive Manufacturing of Polymers: Numerical and Experimental Investigations

Thermal, Tensile and Fatigue Behaviors of the PA6, Short Carbon Fiber-Reinforced PA6, and Continuous Glass Fiber-Reinforced PA6 Materials in Fused Filament Fabrication (FFF)

Analysis of Thermal Behavior in 3D Printing of Continuous Fiber Reinforced Polymer Composites

Simulation of temperature profile in fused filament fabrication 3D printing method

Investigating gradient temperature control for enhanced interfacial bonding behavior in material extrusion 3D printing continuous fiber reinforced polymer composites

Temperature Analyses in Fused Filament Fabrication: From Filament Entering the Hot-End to the Printed Parts

The Adhesive Mechanism and Thermal Analysis of Fibers in the FDM Process

Thermal history based prediction of interlayer bond strength in parts manufactured by material extrusion additive manufacturing

Validation of a Finite Element Model for Fused Filament Fabrication Additive Manufacturing

Modelling of the temperature and residual stress fields during 3D printing of polymer composites