Abstract:Purpose Temperature is a critical factor in the fused filament fabrication (FFF) process, which affects the flow behavior and adhesion of the melted filament and the mechanical properties of the final object. Therefore, modeling and predicting temperature in FFF is crucial for achieving high-quality prints, repeatability, process control and failure prediction. This study aims to investigate the melt deposition and temperature profile in FFF both numerically and experimentally using different Acrylonitrile Butadiene Styrene single-strand specimens. The process parameters, including layer thickness, nozzle temperature and build platform temperature, were varied. Design/methodology/approach COMSOL Multiphysics software was used to perform numerical simulations of fluid flow and heat transfer for the printed strands. The polymer melt/air interface was tracked using the coupling of continuity equation, equation of motion and the level set equation, and the heat transfer equation was used to simulate the temperature distribution in the deposited strand. Findings The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an infrared (IR) thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the three-dimensional (3D) printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand. Originality/value The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an IR thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the 3D printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand.

Validation of a Finite Element Model for Fused Filament Fabrication Additive Manufacturing

Experimental Study of the Process Failure Diagnosis in Additive Manufacturing Based on Acoustic Emission

Application of Numerical Modeling and Finite Element Analysis in Fused Filament Fabrication: A Review

Finite Difference Modeling and Experimental Investigation of Cyclic Thermal Heating in the Fused Filament Fabrication Process

Thermal analysis of fused deposition modeling process based finite element method: Simulation and parametric study

Insights into Temperature Simulation and Validation of Fused Deposition Modeling Processes

Efficient simulation of the heat transfer in fused filament fabrication

Additive Manufacturing of Composite Polymers: Thermomechanical FEA and Experimental Study

Finite Element Analysis of Additive Manufacturing Based on Fused Deposition Modeling: Distortions Prediction and Comparison With Experimental Data

Validation of a finite element method for simulation of components produced by continuous carbon fiber reinforced additive manufacturing

Temporally continuous thermofluidic-thermomechanical modeling framework for metal additive manufacturing

Fused Filament Fabrication Process: A Review of Numerical Simulation Techniques

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Heat Transfer and Adhesion Study for the FFF Additive Manufacturing Process

Temperature Analyses in Fused Filament Fabrication: From Filament Entering the Hot-End to the Printed Parts

Finite Element Modeling of Additive Manufacturing in Case of Metal Parts

Monitoring of fused filament fabrication (FFF): An infrared imaging and machine learning approach

Developing the AM G-code based thermomechanical finite element platform for the analysis of thermal deformation and stress in metal additive manufacturing process

Simulation of temperature profile in fused filament fabrication 3D printing method

SENSING IN-SITU TEMPERATURES BY COORDINATES IN FUSED FILAMENT FABRICATION FOR IDENTIFYING INTERLAYER ANISOTROPIC MECHANICAL PROPERTIES AND ENABLING POST-FEM ANALYSIS

Using Finite Element Analysis in the 3D Printing of Metals