Abstract:Purpose Temperature is a critical factor in the fused filament fabrication (FFF) process, which affects the flow behavior and adhesion of the melted filament and the mechanical properties of the final object. Therefore, modeling and predicting temperature in FFF is crucial for achieving high-quality prints, repeatability, process control and failure prediction. This study aims to investigate the melt deposition and temperature profile in FFF both numerically and experimentally using different Acrylonitrile Butadiene Styrene single-strand specimens. The process parameters, including layer thickness, nozzle temperature and build platform temperature, were varied. Design/methodology/approach COMSOL Multiphysics software was used to perform numerical simulations of fluid flow and heat transfer for the printed strands. The polymer melt/air interface was tracked using the coupling of continuity equation, equation of motion and the level set equation, and the heat transfer equation was used to simulate the temperature distribution in the deposited strand. Findings The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an infrared (IR) thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the three-dimensional (3D) printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand. Originality/value The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an IR thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the 3D printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand.

Temperature Analyses in Fused Filament Fabrication: From Filament Entering the Hot-End to the Printed Parts

Finite Difference Modeling and Experimental Investigation of Cyclic Thermal Heating in the Fused Filament Fabrication Process

In-Situ Temperature Monitoring of ABS During Fused Filament Fabrication (FFF) Process With Varying Process Parameters

Simulation of temperature profile in fused filament fabrication 3D printing method

SENSING IN-SITU TEMPERATURES BY COORDINATES IN FUSED FILAMENT FABRICATION FOR IDENTIFYING INTERLAYER ANISOTROPIC MECHANICAL PROPERTIES AND ENABLING POST-FEM ANALYSIS

Numerical Simulation and Printability Analysis of Fused Deposition Modeling with Dual-Temperature Control

Investigation on the Coalescence of Filaments in Fused Filament Fabrication Process for Amorphous Polyether Ketone Ketone for Varying Nozzle Diameters and Chamber Temperatures

Experimental and numerical investigations on heat transfer in fused filament fabrication 3D-printed specimens

Insights into Temperature Simulation and Validation of Fused Deposition Modeling Processes

Heat Transfer and Adhesion Study for the FFF Additive Manufacturing Process

Analysis of Thermal Behavior in 3D Printing of Continuous Fiber Reinforced Polymer Composites

Efficient simulation of the heat transfer in fused filament fabrication

Validation of a Finite Element Model for Fused Filament Fabrication Additive Manufacturing

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Interfacial Bonding During Multi-Material Fused Deposition Modeling (FDM) Process Due to Inter-Molecular Diffusion

Modeling and self-supporting printing simulation of fuse filament fabrication

Experimental and Thermal Analysis of Desktop FDM 3D Printers "Ender 3" and "CR-10S Pro" Hot Ends

Temperature-compensated Constitutive Model of Fused Filament Fabrication 3D Printed PLA Materials with Full Extrusion Temperatures

Monitoring of fused filament fabrication (FFF): An infrared imaging and machine learning approach

The Adhesive Mechanism and Thermal Analysis of Fibers in the FDM Process

The Transferability and Design of Commercial Printer Settings in PLA/PBAT Fused Filament Fabrication.