Abstract:Purpose Temperature is a critical factor in the fused filament fabrication (FFF) process, which affects the flow behavior and adhesion of the melted filament and the mechanical properties of the final object. Therefore, modeling and predicting temperature in FFF is crucial for achieving high-quality prints, repeatability, process control and failure prediction. This study aims to investigate the melt deposition and temperature profile in FFF both numerically and experimentally using different Acrylonitrile Butadiene Styrene single-strand specimens. The process parameters, including layer thickness, nozzle temperature and build platform temperature, were varied. Design/methodology/approach COMSOL Multiphysics software was used to perform numerical simulations of fluid flow and heat transfer for the printed strands. The polymer melt/air interface was tracked using the coupling of continuity equation, equation of motion and the level set equation, and the heat transfer equation was used to simulate the temperature distribution in the deposited strand. Findings The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an infrared (IR) thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the three-dimensional (3D) printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand. Originality/value The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an IR thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the 3D printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand.

Thermal analysis of fused deposition modeling process based finite element method: Simulation and parametric study

Insights into Temperature Simulation and Validation of Fused Deposition Modeling Processes

Application of Numerical Modeling and Finite Element Analysis in Fused Filament Fabrication: A Review

Developing the AM G-code based thermomechanical finite element platform for the analysis of thermal deformation and stress in metal additive manufacturing process

Finite Difference Modeling and Experimental Investigation of Cyclic Thermal Heating in the Fused Filament Fabrication Process

Heat Transfer and Adhesion Study for the FFF Additive Manufacturing Process

Validation of a Finite Element Model for Fused Filament Fabrication Additive Manufacturing

Simulation of temperature profile in fused filament fabrication 3D printing method

Additive Manufacturing of Composite Polymers: Thermomechanical FEA and Experimental Study

Numerical Simulation and Printability Analysis of Fused Deposition Modeling with Dual-Temperature Control

Interfacial Bonding During Multi-Material Fused Deposition Modeling (FDM) Process Due to Inter-Molecular Diffusion

Modelling of the temperature and residual stress fields during 3D printing of polymer composites

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Thermal Analysis for Simulation of Metal Additive Manufacturing Process Considering Temperature- and History-Dependent Material Properties

Finite Element Analysis of Additive Manufacturing Based on Fused Deposition Modeling: Distortions Prediction and Comparison With Experimental Data

A High-Fidelity Thermal Model for a Novel Droplet-Based Additive Manufacturing Process for Polymers

Numerical investigation of thermal loading on stainless steel during laser powder bed fusion

Modeling of Bond Formation Between Polymer Filaments in the Fused Deposition Modeling Process

Multi-scale modeling and simulation of additive manufacturing based on fused deposition technique

Temporally continuous thermofluidic-thermomechanical modeling framework for metal additive manufacturing

Thermo-Mechanical Modeling of Wire-Fed Electron Beam Additive Manufacturing