Abstract:To reveal the coupling mechanism between melt superheat and ultrasonic action, Ti48Al2Cr2Nb2.5C alloy was prepared by arc melting with ultrasound treatment under different temperature gradients. And numerical simulation, microstructure evolution and Vickers hardness were researched in detail. Simulation results indicate that there are weak acoustic active zone (WZ) and the strong acoustic active zone (SZ) defined by acoustic pressure distribution. The acoustic pressure in SZ is over 10 MPa with an intense acoustic cavitation effect, and the acoustic streaming effect is significant in UC 350 due to the higher acoustic pressure and fluid velocity of 0.19 m/s. Experiment results reveal that the lamellar colony size increases from 39.9 to 67.3 mu m and then decreases to 50.9 mu m, and the aspect ratio of Ti2AlC decreases from 6.5 to 3.3 with overheating increasing in WZ. However, Al segregation is severe. In SZ, the lamellar colony size decreases from 80.3 to 43.7 pm and then increases to 56.1 mu m. The aspect ratio of Ti2AlC decreases from 3.9 to 2.5. From UC 150 to UC 250 in WZ, temperature gradient increasing suppresses the ultrasonic refinement effect. With overheating increasing, the critical ultrasonic cavitation intensity decreases, and the acoustic cavitation effect increases, refining the lamellar colony and Ti2AlC. The stronger acoustic pressure and acoustic streaming effect increase the nucleation rate to refine the lamellar colony and element distribution uniformly in SZ. In WZ, Vickers hardness increases from 191.4 to 223 HV and then decreases to 211.2 HV. Vickers hardness increases from 211.3 to 227.7 HV but decreases to 208.4 HV in UC 300 and then decreases to 208.8 HV in SZ. The highest Vickers hardness in WZ and SZ are in UC 350. Lamellar colony refinement, the aspect ratio of Ti2AlC reduction and Al segregation attenuation improve the Vickers hardness. (C) 2021 Elsevier B.V. All rights reserved.

Correlations to Predict Microstructure and Mechanical Properties of Ultrasonically Cast Metal Matrix Nanocomposites as a Function of Treatment Time

Microstructure Characteristics of A356 Nanocomposites Manufactured via Ultrasonic Cavitation Processing Under Controlled Solidification Conditions

Processing, Microstructure and Mechanical Properties of Micro-Sic Particles Reinforced Magnesium Matrix Composites Fabricated by Stir Casting Assisted by Ultrasonic Treatment Processing

Effects of high intensity ultrasonic wave in the fabrication of metallic matrix composites (MMCs)

Ultrasound Cavitation Induced Nucleation in Metal Solidification: an Analytical Model and Validation by Real-Time Experiments.

Regulating the Macro/Microstructure and Mechanical Properties of Ti2aln/Ti46al4nb1mo Composites Via Ultrasonic Treatment

Effects of High Intensity Ultrasonic During MMCp Fabrication

Processing, Microstructure and Mechanical Properties of Magnesium Matrix Nanocomposites Fabricated by Semisolid Stirring Assisted Ultrasonic Vibration

Microscopic impacts of ultrasonic vibration on interfacial strength of SiCp/Al composites

Effects of nanoparticles on the solution treatment and mechanical properties of nano-SiCp/Al-Cu composites

Microstructure and Mechanical Properties of Cu-CoatedCarbon-Nanotubes-Reinforced Aluminum Matrix Composites Fabricated by Ultrasonic-Assisted Casting

Precipitation behavior and mechanical properties of Al-Zn-Mg-Cu matrix nanocomposites: Effects of SiC nanoparticles addition and heat treatment

An Investigation of Nanoparticle Wetting, Grain Refinement and Mechanical Property Enhancement in Aluminum Matrix Nanocomposites

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Effect of Ultrasonic Vibration on the Grain Refinement and SiC Particle Distribution in Zn-based Composite Filler Metal

Untrasonic-Assisted Fabrication of SiC Nanoparticles Reinforced Aluminum Matrix Composites

Role of Different Fractions of Nano-size SiC and Milling Time on the Microstructure and Mechanical Properties of Al–SiC Nanocomposites

Research of Different Mechanisms in the Weak/strong Acoustic Active Zones on Microstructure Evolution and Mechanical Property of Ti48Al2Cr2Nb2.5C Composites

Experimental Research on Ultrasonic Vibration Milling Metal Matrix Composites Sicp/Al

Influence of ultrasonic parameters on microstructural refinement and defect elimination in ultrasound-assisted laser-based metal additive manufacturing