Abstract:The long-term periodicity and uncontrollable interface properties during the preparation process for silicon carbide fiber reinforced silicon carbide-based composites (SiCf/SiC CMC) make it difficult to thoroughly investigate their mechanical damage behavior under complex loading conditions. To delve deeper into the influence of the interface strength and toughness on the mechanical response of microscopic representative volume element (RVE) models under complex loading conditions, in this work, based on numerical simulation methods, a microscale representative volume element (RVE) with periodic symmetric boundary conditions for the material is constructed. The phase-field fracture theory and cohesive zone model are coupled to capture the brittle cracking of the matrix and the debonding behavior at the fiber/matrix interface. Simulation analysis is conducted for tensile, compressive, and shear loading as well as combined loading, and the validity of the model is verified based on the Chamis theory. Further investigation is conducted into the mechanical response behavior of the microscale RVE model under complex loading conditions in relation to the interface strength and interface toughness. The results indicate that under uniaxial loading, increasing the interface strength leads to a tighter bond between the fiber and matrix, suppressing crack initiation and propagation, and significantly increasing the material's fracture strength. However, compared to the transverse compressive strength, increasing the interface strength does not continuously enhance the strength under other loading conditions. Meanwhile, under the condition of strong interface strength of 400 MPa, an increase in the interface toughness significantly increases the transverse compressive strength of the material. When it increases from 2 J/m2 to 20 J/m2, the transverse compressive strength increases by 28.49%. Under biaxial combined loading, increasing the interface strength significantly widens the failure envelope space under σ2-τ23 combined loading; with the transition from transverse compressive stress to tensile stress, the transverse shear strength shows a trend of first increasing and then decreasing, and when the ratio of transverse shear displacement to transverse tensile/compressive displacement is −1, it reaches the maximum. This study provides strong numerical support for the investigation of the interface properties and mechanical behavior of SiCf/SiC composites under complex loading conditions, offering important references for engineering design and material performance optimization.

Microscopic impacts of ultrasonic vibration on interfacial strength of SiCp/Al composites

Study on effect of vibration amplitude on cutting performance of SiCp/Al composites during ultrasonic vibration–assisted milling

Finite Element and Experimental Analysis of Ultrasonic Vibration Milling of High-Volume Fraction SiCp/Al Composites

Material deformation and removal mechanism of SiCp/Al composites in ultrasonic vibration assisted scratch test

Experimental and FEM study of surface formation and deformation mechanism of SiCp/Al composites in laser-ultrasonic vibration assisted turning

Numerical analysis of physical quantities during ultrasonic vibration assisted cutting of SiCp/Al composites

Mechanism and feasibility of ultrasonic-assisted milling to improve the machined surface quality of 2D Cf/SiC composites

Material removal and damage formation mechanisms induced by periodic indentation during ultrasonic vibration-assisted scratching of SiC f /SiC composites

Pulsed Laser Ultrasonic Vibration-Assisted Cutting of SiCp/Al Composites through Finite Element Simulation and Experimental Research

Study on formation mechanism of edge defects of high-volume fraction SiCp/Al composites by longitudinal-torsional ultrasonic vibration-assisted milling

On understanding the cutting mechanism of SiCp/Al composites during ultrasonic elliptical vibration-assisted machining

Mechanical Response and Microstructure Revolution of SiC particle-reinforced Al-MMCs under Ultrasonic Loading

The Influence of the Interface on the Micromechanical Behavior of Unidirectional Fiber-Reinforced Ceramic Matrix Composites: An Analysis Based on the Periodic Symmetric Boundary Conditions

Experimental investigations on ultrasonic elliptical vibration turning of SiCp/Al composites

Effects of High Intensity Ultrasonic Processing on Preparation of SiC Nano-Particles Reinforced Magnesium Matrix Composite

Friction characterization of SiCp/Al composites by 3D ultrasonic vibration-assisted milling

In situ mechanical testing of an Al matrix composite to investigate compressive plasticity and failure on multiple length scales

Longitudinal amplitude effect on material removal mechanism of ultrasonic vibration-assisted milling 2.5D C/SiC composites

Solidified Microstructure of SiCp/Al Composites Bonds under Ultrasonic Vibration and Their Fracture Characteristics

Simulation and Experimental Study of C/SiC Composites by Laser-ultrasonic Hybrid Micromachining

Ductile-brittle transition mechanism of SiC particle-reinforced Al-MMCs under ultrasonic assisted grinding with single grain