Abstract:The preparation of large-scale magnesium (Mg) alloy parts by wire arc additive manufacturing (WAAM) has broad application prospects, including automotive and aerospace industries. The chemical composition of Mg alloy wires plays a critical role in determining mechanical properties of WAAM Mg alloys. However, types of Mg alloy wires for WAAM need to be extended, in order to improve mechanical properties. Therefore, in the present work, a novel ATZM31 Mg alloy wire has been prepared and applied to the cold metal transfer (CMT)-WAAM process. This study focuses on understanding the forming quality, microstructure evolution, and mechanical properties of the ATZM31 alloy thin-wall component fabricated by WAAM. The results show that the Mg alloy thin-wall component possesses satisfactory formability, with minor sidewall roughness. The ATZM31 thin-wall component is mainly composed of columnar dendrites and equiaxed dendrites of the α-Mg phase, with the η-Al 8 Mn 5 phase distributes dispersedly at grain boundaries. The area fraction of the η-Al 8 Mn 5 phase is estimated to be ∼0.21% based on the statistical analysis of SEM images. Due to different cooling behaviors, the distribution of grain size along the build direction of the thin-walled component is uneven. The average grain size is ∼46 μm, ∼74 μm and ∼61 μm at the bottom, middle and top of the ATZM31 alloy thin-wall component, respectively. From the substrate to the top of the ATZM31 alloy thin-wall component, the hardness decreases gradually. The ultimate tensile strength along the deposition direction and build direction are ∼225 MPa and ∼214 MPa, respectively, without pronounced anisotropy. The ATZM31 alloy thin-wall component fabricated by WAAM exhibits a comparable ultimate tensile strength to forged AZ31 Mg alloys and weaker anisotropy than wrought Mg alloys.

Development of a High Strength Magnesium Alloy for Wire Arc Additive Manufacturing

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Wire arc additive manufacturing of a novel ATZM31 Mg alloy: Microstructure evolution and mechanical properties

Development of a New High Strength Alloy from Low Alloy Steel Wire by Innovative Additional Cold Wire Feeding Used in Wire Arc Additive Manufacturing

Novel Magnesium Nanocomposite for Wire-Arc Directed Energy Deposition

Characterisation of a High-Performance Al-Zn-Mg-Cu Alloy Designed for Wire Arc Additive Manufacturing

Characterisation of a High-Performance Al–Zn–Mg–Cu Alloy Designed for Wire Arc Additive Manufacturing

Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

Wire Arc Additive Manufacturing of Al-Mg Alloy with the Addition of Scandium and Zirconium

Wire Arc Additive Manufacturing: A Comprehensive Review and Research Directions

A Review of High-Strength Aluminum-Copper Alloys Fabricated by Wire Arc Additive Manufacturing: Microstructure, Properties, Defects, and Post-processing

Microstructure and mechanical properties of WE43 magnesium alloy fabricated by wire-arc additive manufacturing

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Wire Arc Additive Manufacturing with Novel Al-Mg-Si Filler Wire—Assessment of Weld Quality and Mechanical Properties

Wire and Arc Additive Manufacturing of High-Strength Al–Zn–Mg Aluminum Alloy

Printing High-Strength High-Elongation Al4043 Alloy Using UNS A94043 Welding Wires through Wire Arc Additive Manufacturing

On the fabrication of finer grain structure through using finer wire diameter for wire arc additive manufacturing of AZ31B magnesium alloy

Magnesium Alloy 3D Printing by Wire and Arc Additive Manufacturing (WAAM)

Formability, microstructure evolution and mechanical properties of wire arc additively manufactured AZ80M magnesium alloy using gas tungsten arc welding

Wire-arc additive manufacturing of AZ31 magnesium alloy fabricated by cold metal transfer heat source: Processing, microstructure, and mechanical behavior