Abstract:Cryogenic treatment has high potential for improving the deformation behavior through the recrystallization at a low temperature. In this work, true stress-strain curves were obtained via compression tests to understand the deformation behavior of an AA7075 under cryogenic conditions. Results showed a significant improvement in the flow stress of AA7075, increasing from 260 to 560 MPa at the yield point. The strain hardening exponent (n) also increased from 0.25 to 0.35 after deformation at cryogenic temperatures. The presence of Al2CuMg phase influenced the deformation texture of the tested aluminum alloy, resulting in more elongated grains and fine sub-grains after deformation at cryogenic temperatures, due to the hindered recrystallization. Microstructure evolution after deformation at room and cryogenic temperatures was investigated using EBSD technique to characterize texture and recrystallized grains. The results indicated that the spacing of the high-angle grain boundaries (HAGBs) in the sample deformed at room temperature was slightly larger than in the cryogenically treated sample. The alloy deformed at the cryogenic temperature exhibited a higher strain hardening exponent (n = 0.35) compared to room temperature deformation (n = 0.25). Furthermore, finite element analysis supported the experimental findings, showing that the Plastic Equivalent Strain (PEEQ) of the model tested at cryogenic temperature was higher than at room temperature, attributed to grain refinement during low-temperature deformation. The calculated effective stress responses at cryogenic temperatures for the investigated flow stress aligned well with the experimental results. These new aspects and mechanisms of deformation of aluminum alloys at cryogenic temperatures can improve the formability of high-strength alloys in the future production of more complex and integrated lightweight components.

Modification of residual stress and microstructure in aluminium alloy by cryogenic treatment

Relief of Residual Stresses in 7050 Aluminum Alloy by Deep Cryogenic Treatment

Effect of Cryogenic Treatment on Residual Stress and Microstructure of 6061 Aluminum Alloy and Optimization of Parameters

Effect of Deep Cryogenic Treatment on the Artificial Aging Behavior of 6082 Aluminum Alloy

Optimization of Cryogenic Treatment Parameters for the Minimum Residual Stress

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Effect of deep cryogenic treatment on the microstructure and mechanical properties of Al–Cu–Mg–Ag alloy

Evaluation of residual stress relief of aluminum alloy 7050 by using crack compliance method

The Influence of Cryogenic Treatment on the Microstructure and Mechanical Characteristics of Aluminum Silicon Carbide Matrix Composites

The improvement of deformability in AA7075 alloy through cryogenic treatment and its correlation with microstructural evolution and FE modelling

Mechanism of cryogenic, solid solution and aging compound heat treatment of die-cast Al alloys considering microstructure variation

Effect of deep cryogenic treatment on microstructures and mechanical properties of automotive 6063Al alloy

Effect of Cryorolling and Ageing on the Microstructure and Mechanical Properties of Al 7085 Alloy

Influence of shallow and deep cryogenic treatment on the residual state of stress of 4140 steel

Effect of a Novel Thermomechanical Treatment on Microstructure and Mechanical Properties of 7034 Aluminum Alloy

An investigation of cryogenic-aging process attemptted to alleviate mechanical anisotropy of 7055 thick plate

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Achieving synergistic improvement of wear and mechanical properties in Ti–6Al–4V alloy by multiple cryogenic treatment

The Strengthening Role of Cryogenic Treatment in the Mechanical Properties and Abrasive Wear of Low Alloy Wear-Resistant Steel

Effect of Deep Cryogenic Treatment on the Artificial Ageing Behavior of SiCp–AA2009 Composite

Effects of deep cryogenic treatment on microstructural evolution and alloy phases precipitation of a new low carbon martensitic stainless bearing steel during aging