Abstract:Cryogenic treatment has high potential for improving the deformation behavior through the recrystallization at a low temperature. In this work, true stress-strain curves were obtained via compression tests to understand the deformation behavior of an AA7075 under cryogenic conditions. Results showed a significant improvement in the flow stress of AA7075, increasing from 260 to 560 MPa at the yield point. The strain hardening exponent (n) also increased from 0.25 to 0.35 after deformation at cryogenic temperatures. The presence of Al2CuMg phase influenced the deformation texture of the tested aluminum alloy, resulting in more elongated grains and fine sub-grains after deformation at cryogenic temperatures, due to the hindered recrystallization. Microstructure evolution after deformation at room and cryogenic temperatures was investigated using EBSD technique to characterize texture and recrystallized grains. The results indicated that the spacing of the high-angle grain boundaries (HAGBs) in the sample deformed at room temperature was slightly larger than in the cryogenically treated sample. The alloy deformed at the cryogenic temperature exhibited a higher strain hardening exponent (n = 0.35) compared to room temperature deformation (n = 0.25). Furthermore, finite element analysis supported the experimental findings, showing that the Plastic Equivalent Strain (PEEQ) of the model tested at cryogenic temperature was higher than at room temperature, attributed to grain refinement during low-temperature deformation. The calculated effective stress responses at cryogenic temperatures for the investigated flow stress aligned well with the experimental results. These new aspects and mechanisms of deformation of aluminum alloys at cryogenic temperatures can improve the formability of high-strength alloys in the future production of more complex and integrated lightweight components.

Optimization of Cryogenic Treatment Parameters for the Minimum Residual Stress

Effect of Cryogenic Treatment on Residual Stress and Microstructure of 6061 Aluminum Alloy and Optimization of Parameters

Relief of Residual Stresses in 7050 Aluminum Alloy by Deep Cryogenic Treatment

Finite Element Method Simulation for Residual Stress in Quenched Aluminum Alloy Thick-Plate and Its Effect on Machining Distortion

Pre-stretching Process and Its Application in Reducing Residual Stress of Quenched 7075 Aluminum Alloy Thick-Plates

Minimization of Residual Stress in an Al-Cu Alloy Forged Plate by Different Heat Treatments

Modification of residual stress and microstructure in aluminium alloy by cryogenic treatment

Effect of Cryogenic Treatments on Mechanical Properties of 2a11 Aluminum Alloy

Effect of Cryogenic Treatment and Thermal Shock on Residual Stresses, Structure and Properties of Alloy D16

Evaluation of residual stress relief of aluminum alloy 7050 by using crack compliance method

Optimization of Cryogenic Process Parameters for the Minimization of Surface Residual Stress in Pure Iron Using Taguchi Design

The improvement of deformability in AA7075 alloy through cryogenic treatment and its correlation with microstructural evolution and FE modelling

Effect of Pretreatment and Cryogenic Temperatures on Mechanical Properties and Microstructure of Al-Cu-Li Alloy

Numerical Analysis of Residual Stresses in Quenched High-Strength Aluminum Alloy Ultra-Thick Plates and their Reduction through Single-Side Cold Compression Method

Numerical and Experimental Research on Cold Compression Deformation Method for Reducing Quenching Residual Stress of 7A85 Aluminum Alloy Thick Block Forging

Effect of Deep Cryogenic Treatment on the Artificial Aging Behavior of 6082 Aluminum Alloy

Effects of Deformation at High, Medium, and Cryogenic Temperatures on the Microstructures and Mechanical Properties of Al-Zn-Mg-Cu Alloys

Influence of Cryogenic Treatment and Thermal Shock on Quenching Stresses and Properties of Alloy D16

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Mechanism of cryogenic, solid solution and aging compound heat treatment of die-cast Al alloys considering microstructure variation

Effect of deep cryogenic treatment on microstructures and mechanical properties of automotive 6063Al alloy