Abstract:In this study, 7A85 aluminum alloy was subjected to 20% three-dimensional (3D) deformation at different temperatures (−196, 25, 250, and 480 °C), followed by solid solution, water quenching, 3% cold deformation, and retrogression and re-aging (RRA) treatment. The microstructural evolution and 3D mechanical properties, fracture toughness, electrical conductivity, and corrosion resistance of the alloy under different deformation processes were analyzed for comparison. The results indicated that conducting the 3D deformation process prior to solution treatment significantly improved the strength and fracture toughness of the alloy as compared to the undeformed (UD) specimen, and maintained its good corrosion resistance under the RRA treatment. In addition, with the decrease of the deformation temperature, the greater flow stress strongly sheared and crushed the coarse second-phase particles into fine particles, thus facilitating their full dissolution in the aluminum matrix during subsequent solution treatment and increasing the driving force for aging precipitation. Furthermore, more dislocations were introduced at low-temperature deformation, thus providing more nucleation sites for static recrystallization during solution treatment and refining grains. Ultimately, the densest precipitates and the finest equiaxed grains with the narrowest grain boundary precipitate-free zones (PFZs) were acquired for the cryogenic deformation (CD) sample, resulting in the highest ultimate tensile strength (UTS), elongation (EL) with the least anisotropy, and fracture toughness of the CD specimen. The optimal comprehensive performance was obtained for the CD specimen with the average 3D UTS, average 3D yield strength (YS), average 3D EL, and fracture toughness of 545 MPa, 476 MPa, 16%, and 42.49 MPa·m 1/2 , respectively, which were respectively 2.3%, 0.2%, 18.5%, and 21.4% higher than those of the UD specimen.

Effect of Cryogenic Treatment and Thermal Shock on Residual Stresses, Structure and Properties of Alloy D16

Influence of Cryogenic Treatment and Thermal Shock on Quenching Stresses and Properties of Alloy D16

Effect of Deep Cryogenic Treatment on the Artificial Aging Behavior of 6082 Aluminum Alloy

Effect of deep cryogenic treatment on microstructures and mechanical properties of automotive 6063Al alloy

Effect of Cryogenic Treatment on Residual Stress and Microstructure of 6061 Aluminum Alloy and Optimization of Parameters

Effect of deep cryogenic treatment on the microstructure and mechanical properties of Al–Cu–Mg–Ag alloy

Optimization of Cryogenic Treatment Parameters for the Minimum Residual Stress

Effect of Cryogenic Treatments on Mechanical Properties of 2a11 Aluminum Alloy

Relief of Residual Stresses in 7050 Aluminum Alloy by Deep Cryogenic Treatment

Effect of heat treatment process on microstructure and dimensional stability of 2A12 aluminum alloy

Effect of Cryogenic Treatment on the Mechanical Properties of Alloy Steel 16MnCr5

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Mechanism of cryogenic, solid solution and aging compound heat treatment of die-cast Al alloys considering microstructure variation

Microstructures and Cryogenic Mechanical Properties of Spray Deposited 2195 Al–Cu–Li Alloy with Different Heat Treatments

Effect of Pretreatment and Cryogenic Temperatures on Mechanical Properties and Microstructure of Al-Cu-Li Alloy

The effects of heat treatment on the microstructure and cyclic behavior of A7N01-T4 aluminum alloy

Cryogenic Investigations into the Effect of Impact-Oscillatory Loading on Changes in the Mechanical Properties and Structural Condition of VT23M Two-Phase Titanium Alloy

Effect of three-dimensional deformation at different temperatures on microstructure, strength, fracture toughness and corrosion resistance of 7A85 aluminum alloy

Effects of cryogenic treatments on phase transformations, microstructure and mechanical properties of near βTi alloy

Effect of Cryogenic Treatment on Internal Residual Stresses of Hydrogen-Resistant Steel

Effect of a Novel Thermomechanical Treatment on Microstructure and Mechanical Properties of 7034 Aluminum Alloy