Abstract:Due to high temperature strength (hot strength), excellent corrosion resistance and high strength-to-weight ratio, Ti-6Al-4V alloy is considered as a potential candidate for extensive applications in aerospace and biomedical engineering. But, alloy's low thermal conductivity and extreme chemical affinity (towards tool substrate and coating materials) often cause an aggressive cutting environment with a tremendous rise in cutting zone temperature, premature tool wear, and disappointing surface integrity during conventional machining processes. In order to achieve desired machining yield without opting for any coolant, selection of proper cutting tool (based on their geometry and properties) is indeed vital. Thus, the present work examined the performance of MTCVD-TiCN-Al 2 O 3 -TiOCN multi-layer coated carbide and PVD TiN single layer coated composite ceramic (Al 2 O 3 /TiCN) tool inserts during dry machining of Ti-6Al-4V. Higher friction coefficient (of the coating system) was revealed for the ceramic tool which caused substantial temperature rise at tool-tip. On the other hand, carbide insert imparted lower cutting force (beyond = 80 m/min) than ceramic insert due to its better thermo-chemical stability. Coating peel-off and tool flaking were witnessed for ceramic insert due to its thermal instability at higher cutting speeds; while carbide tool was mainly affected by material adhesion, abrasion, and chip fusion (adhesion of broken chip-fragments over tool surface due to high pressure and temperature). It was experienced that induced cutting heat significantly affected chip morphology under a dry cutting environment. Up to = 130 m/min, ceramic tool exhibited lower flank wear than carbide tool.

Effects of VC additive on cutting compatibility of TiB2-based cermet cutting tools and Ti6Al4V alloy

Influence of Cutting Conditions on the Wear Resistance of Tools with a TiB2 Coating during Titanium Alloy Machining

Evaluation of the performance of coated carbide tools in face milling TC6 alloy under dry condition

Effect of tungsten carbide content on the tribological behavior of TiB2–TiC-based cermets

Cutting Performance of TiN/TiSiN Coated Tool during Turning of Ti6Al4V Titanium Alloy

An Investigation of the Effect of Novel Mono/Bi-Layered PVD-Coated WC Tools on the Machinability of Ti-5Al-5V-5Mo-3Cr

Investigation of the Wear Performance of TiB2 Coated Cutting Tools during the Machining of Ti6Al4V Alloy

Enhancing cutting performance of Ti(C,N)‐Based cermet tools on nodular cast iron by incorporating high‐entropy carbide

Effect of SiC Addition to Al2O3 Ceramics Used in Cutting Tools

Cutting performance of cubic boron nitride-coated tools in dry turning of hardened ductile iron

Effects of nano-Al2O3 addition on microstructure, mechanical properties, and wear resistance of Ti(C, N)-based cermets

Cutting Performance and Wear Mechanism of Submicron and Ultrafine Ti(C, N)-based Cermets

Comparative experimental study on application feasibiility of MTCVD TiCN-Al2O3-TiOCN multi-layer coated carbide and PVD TiN single layer coated composite ceramic inserts during dry machining of Ti-6Al-4V

Effect of Si3N4 Additive on Microstructure and Mechanical Properties of Ti(C,N)-Based Cermet Cutting Tools

Enhancing Tool Performance in High-Speed End Milling of Ti-6Al-4V Alloy: The Role of AlCrN PVD Coatings and Resistance to Chipping Wear

Performance and wear mechanisms of PCD and pcBN cutting tools during machining titanium alloy Ti6Al4V

WEAR MECHANISMS AND PERFORMANCE OF COATED INSERTS DURING FACE MILLING OFTC11ANDTC17ALLOYS

Effects of Ti Containing Cu-Based Alloy on Sintering Mechanism, Element Diffusion Behavior and Physical Properties of Glass-Ceramic Bond for Cubic Boron Nitride Abrasive Tool Materials

Influence of different wet-blasting pressure on the surface integrity and tool cutting performance of hybrid CVD-TiN/TiCN/α-Al2O3/TiN coated tools

Fabrication and Cutting Performance of CVD Diamond Coated Inserts with Different Coating Thickness in Dry Turning Aluminum Alloy

Experimental Investigation on Tool Wear Characteristics of PVD and CVD Coatings During Face Milling of Ti6242S and Ti-555 Titanium Alloys