Abstract:At present, the most common type of SOFC is anode-supported SOFC (AS-SOFC), in which the cell is mechanically supported by the thick fuel electrode layer. Recently, Metal-supported SOFCs (MS-SOFCs) have attracted attention because of their potential for low cost and high mechanical robustness. However, the fabrication process of MS-SOFCs has not been established. The mechanical behavior of the cells under high temperature operation has not been clarified. In this study, we fabricated prototype MS-SOFCs using the plasma spray method. The cell was tested by electrochemical measurements, residual stress measurements, and SEM/EDX to clarify the mechanical behavior of MS-SOFCs under high temperature operation. The layers of anode (NiO-YSZ), electrolyte (LSGM9182), and cathode (LSCF6428) were formed on a metal substrate (SUS430) by atmospheric pressure plasma spraying (APS) to fabricate a single cell of MS-SOFC. Open circuit voltage, AC impedance, and I-V measurements were performed at 600°C, 650°C, and 700°C. The residual stress of LSGM9182 electrolyte was evaluated by cosα method [1] under the cell operation condition using specially designed chamber. The MS-SOFC with thicker electrode layers showed the much lower OCV than that of theoretical. In addition, the electrolyte had vertical cracks between cathode and anode after the 2nd thermal cycle. However the MS-SOFC with thinner electrode layers showed the higher OCV, which was nearly theoretical value, and much better I-V characteristics than the cell with thicker electrodes. Electrochemical impedance measurement revealed the plasma sprayed electrodes showed acceptable performance even though its microstructure was not optimized. The residual stress of LSGM electrolyte in the cell did not change so much during the cell operation. This might be caused by existence of small cracks in the electrolyte layer. This research was financially supported by NEDO. [1] K.Tanaka, Journal of the Society of Materials Science,japan,vol.66,No.7 (2017) 479-487

Self-Sealing Metal-Supported SOFC Fabricated by Plasma Spraying and Its Performance under Unbalanced Gas Pressure

Performance and Stability of Plasma-Sprayed 10 × 10 cm 2 Self-sealing Metal-Supported Solid Oxide Fuel Cells

Characterization of Self-Sealed Metal Supported SOFCs with the Very Low Pressure Plasma Sprayed ScSZ Electrolyte

Development of ScSZ Electrolyte by Very Low Pressure Plasma Spraying for High-Performance Metal-Supported SOFCs

Electrochemical Performance and Mechanical Stress Evaluation of Metal-Supported Solid Oxide Fuel Cells Fabricated By Plasma Spray Method

Scandia-stabilized Zirconia Electrolyte with Improved Interlamellar Bonding by High-Velocity Plasma Spraying for High Performance Solid Oxide Fuel Cells

Performance of Tubular Solid Oxide Fuel Cell Assembled with Plasma-Sprayed Sc2O3–ZrO2 Electrolyte

Performance of Plasma-Sprayed Bi2O3–Er2O3–WO3 for Intermediate-Temperature Solid Oxide Fuel Cells (It-Sofcs)

Performance of YSZ Electrolyte Layer Deposited by Atmospheric Plasma Spraying for Cermet-Supported Tubular SOFC

Densification of Plasma-Sprayed YSZ Electrolyte by Suction Filtration Using Submicron/Nanoparticle Suspension for Metal-Supported SOFCs

Thermally Sprayed High-Performance Porous Metal-Supported Solid Oxide Fuel Cells With Nanostructured La0.6sr0.4co0.2fe0.8o3-Delta Cathodes

Performance of Anode-Supported Single-Chamber Solid Oxide Fuel Cells

Preparation of Dual-Pore Anode Supported Sc2o3-Stabilized-Zro2 Electrolyte Planar Solid Oxide Fuel Cell by Phase-Inversion and Dip-Coating

High Performance Tubular Solid Oxide Fuel Cells With Bscf Cathode

Novel Approaches to Prepare the High Performance Dense Electolyte and Interconnect Applicable to SOFC by Atmospheric Plasma Spraying

Development of NiO-GDC Anode by Atmospheric Plasma Spraying for Metal-Supported SOFCs

Development of a Ni/Al 2 O 3 Cermet-Supported Tubular Solid Oxide Fuel Cell Assembled with Different Functional Layers by Atmospheric Plasma-Spraying

Study on the Fabrication and Performance of Very Low Pressure Plasma Sprayed Porous Metal Supported Solid Oxide Fuel Cell

A Symmetrical Solid Oxide Fuel Cell Prepared by Dry-Pressing and Impregnating Methods

Fabrication and Characterization of Ni-SSZ/SSZ/LSM-SSZ Anode-Supported SOFCs by Tape Casting and Single-Step Co-Sintering Techniques

Plasma-sprayed Y2O3-stabilized ZrO2 electrolyte with improved interlamellar bonding for direct application to solid oxide fuel cells