Abstract:Introduction: The cervical spine, pivotal for mobility and overall body function, can be affected by cervical spondylosis, a major contributor to neural disorders. Prevalent in both general and military populations, especially among pilots, cervical spondylosis induces pain and limits spinal capabilities. Anterior Cervical Discectomy and Fusion (ACDF) surgery, proposed by Cloward in the 1950s, is a promising solution for restoring natural cervical curvature. The study objective was to investigate the impacts of ACDF implant design on postsurgical cervical biomechanics and neurorehabilitation outcomes by utilizing a biofield head-neck finite element (FE) platform that can facilitate scenario-specific perturbations of neck muscle activations. This study addresses the critical need to enhance computational models, specifically FE modeling, for ACDF implant design. Materials and methods: We utilized a validated head-neck FE model to investigate spine-implant biomechanical interactions. An S-shaped dynamic cage incorporating titanium (Ti) and polyetheretherketone (PEEK) materials was modeled at the C4/C5 level. The loading conditions were carefully designed to mimic helmet-to-helmet impact in American football, providing a realistic and challenging scenario. The analysis included intervertebral joint motion, disk pressure, and implant von Mises stress. Results: The PEEK implant demonstrated an increased motion in flexion and lateral bending at the contiguous spinal (C4/C5) level. In flexion, the Ti implant showed a modest 5% difference under 0% activation conditions, while PEEK exhibited a more substantial 14% difference. In bending, PEEK showed a 24% difference under 0% activation conditions, contrasting with Ti's 17%. The inclusion of the head resulted in an average increase of 18% in neck angle and 14% in C4/C5 angle. Disk pressure was influenced by implant material, muscle activation level, and the presence of the head. Polyetheretherketone exhibited lower stress values at all intervertebral disc levels, with a significant effect at the C6/C7 levels. Muscle activation level significantly influenced disk stress at all levels, with higher activation yielding higher stress. Titanium implant consistently showed higher disk stress values than PEEK, with an orders-of-magnitude difference in von Mises stress. Excluding the head significantly affected disk and implant stress, emphasizing its importance in accurate implant performance simulation. Conclusions: This study emphasized the use of a biofidelic head-neck model to assess ACDF implant designs. Our results indicated that including neck muscles and head structures improves biomechanical outcome measures. Furthermore, unlike Ti implants, our findings showed that PEEK implants maintain neck motion at the affected level and reduce disk stresses. Practitioners can use this information to enhance postsurgery outcomes and reduce the likelihood of secondary surgeries. Therefore, this study makes an important contribution to computational biomechanics and implant design domains by advancing computational modeling and theoretical knowledge on ACDF-spine interaction dynamics.

The Biomechanical Response of the Lower Cervical Spine Post Laminectomy: Geometrically-Parametric Patient-Specific Finite Element Analyses

Development and validation of a geometrically personalized finite element model of the lower ligamentous cervical spine for clinical applications

Using Finite Element Models to Assess Spinal Cord Biomechanics after Cervical Laminoplasty for Degenerative Cervical Myelopathy

Comparative Analysis of the Biomechanical Characteristics After Different Minimally Invasive Surgeries for Cervical Spondylopathy: A Finite Element Analysis

Adjacent segments biomechanics following lumbar fusion surgery: a musculoskeletal finite element model study

Finite Element Analysis of Implanted Lumbar Spine: Effects of Open Laminectomy plus PLF and Open Laminectomy plus TLIF Surgical Approaches on L3-L4 FSU

Implant Design and Cervical Spinal Biomechanics and Neurorehabilitation: A Finite Element Investigation

Biomechanical analysis of cervical spine (C2–C7) at different flexed postures

Finite Element Based-Analysis for Pre and Post Lumbar Fusion of Adult Degenerative Scoliosis Patients

Biomechanical Analysis of Adjacent Segments after Spinal Fusion Surgery Using a Geometrically Parametric Patient-Specific Finite Element Model

Biomechanical Evaluation Of Two Endoscopic Spine Surgery Methods For Treating Lumbar Disc Herniation: A Finite Element Studies

Biomechanical response of decompression alone in lower grade lumbar degenerative spondylolisthesis--A finite element analysis

Biomechanical study of the stability of posterior cervical expansive open-door laminoplasty combined with bilateral C4/5 foraminotomy and short-segment lateral mass screw fixation: a finite element analysis

A Three-Dimensional Morphological Assessment for Evaluating Pre- and Postsurgery in Cervical Laminoplasty

Biomechanical Effects of Anterior Decompression and Fusion With Cervical Two-Segments Different Internal Fixation Systems: A Finite Element Study

Biomechanical evaluation of different sizes of 3D printed cage in lumbar interbody fusion-a finite element analysis

Biomechanical evaluation on a new type of vertebral titanium porous mini-plate and mechanical comparison between cervical open-door laminoplasty and laminectomy: a finite element analysis

Biomechanical properties analysis of posterior lumbar interbody fusion with transpedicular oblique screw fixation

Biomechanical Comparison of Different Surgical Strategies for Skip-level Cervical Degenerative Disc Disease: A Finite Element Study

Finite element analysis of biomechanical investigation on diverse internal fixation techniques in oblique lumbar interbody fusion

Clinical parameters of laminoplasty and laminectomy with fusion in the treatment of cervical spondylosis and analysis of postoperative sagittal balance