Abstract:In this study, the process of carbon dioxide (CO2) capture directly from ambient air in a conventional monoethanolamine (MEA) absorption process was simulated and optimized using a rate-based model in Aspen Plus. The process aimed to capture a specific amount (148.25 Nm3/h) of CO2 from the air, which was determined by a potential application aiming to produce synthetic methane from the output of a 2.7 MW electrolyser (593 Nm3/h H2). We investigated the technical performance of the process by conducting a sensitivity analysis around different parameters such as air humidity, capture rate defined as a ratio of moles of CO2 captured during the process to the total mole of CO2 in the feed stream, CO2 loading of lean and rich absorption liquids and reboiler temperature, and evaluated the energy consumption and overall cost in this system. In order to meet the design requirement for standard packed columns, the rich absorption liquid was circulated to the top of the absorber. A capture rate of 50% was selected in this process as a baseline. At higher capture rates, the required energy per ton of captured CO2 increases due to a higher steam stripping rate, required in the desorber, and at lower capture rates, the size of equipment, in particular, absorber and blowers increases due to the need for processing a significantly larger volume of air at the given CO2 production volume. At the base case scenario, a reboiler duty of 10.7 GJ/tCO2 and an electrical energy requirement of 1.4 MWh/tCO2 were obtained. The absorber diameter and height obtained were 10.4 and 4.4 m, respectively. The desorber is found to be relatively small at 0.54 m in diameter and 3.0 m in height. A wash water section installed at top of the absorber decreased the MEA loss to 0.28 kg/ton CO2. However, this increased capital cost by around 60% resulting in CO2 capture costs of $1,691 per ton CO2 for the MEA base scenario. Based on the techno-economic analysis, assuming a non-volatile absorbent rather than MEA thereby avoiding a wash water section, and using an absorption column built from cheaper materials, the estimated cost per ton of CO2 produced was reduced to $676/tCO2. The overall cost range was between $273 and $1,227 per ton of CO2 depending on different economic parameters such as electricity ($20–$200/MWh) and heat price ($2–$20/GJ), plant life (15–25 years) and capital expenditure (±30%). In order to reduce the cost further, the use of innovative cheap gas-liquid contactors that operate at lower liquid to gas ratios is crucial.

Aspen plus supported design of pre-combustion CO2 capture processes based on ionic liquids

Cost and Heat Integration Analysis for CO2 Removal Using Imidazolium-Based Ionic Liquid -ASPEN PLUS Modelling Study

Carbon Dioxide Capturing in Temperature/Pressure Swing‐Commercial Processes Using Ionic Liquids

Capturing CO2 by Ionic Liquids and Deep Eutectic Solvents: A Comparative Study Based on Multi-Level Absorbent Screening

Techno-Economic Assessment for CO2 Capture From Air Using a Conventional Liquid-Based Absorption Process

Technical-economic analysis of [Bmim][BF4] for the post-combustion CO2 capture at ”Termocentro” thermoelectric plant, Colombia

Modelling and Process Analysis of Post-Combustion Carbon Capture with the Blend of 2-Amino-2-methyl-1-propanol and Piperazine

Ionic Liquid-Ethanol Mixed Solvent Design for the Post-Combustion Carbon Capture

Improved CO2 Capture Method by Absorption

Simulation and Optimization for Flue Gas CO2 Capture by Energy Efficient Water-Lean Ionic Liquid Solvent

Chemical and Physical Ionic Liquids in CO2 Capture System Using Membrane Vacuum Regeneration

Integrated Gasification Combined Cycle with Carbon Dioxide Capture by Elevated Temperature Pressure Swing Adsorption

CO2 Utilization Via Integration of an Industrial Post-Combustion Capture Process with a Urea Plant: Process Modelling and Sensitivity Analysis

Integrated CO2 Capture and Utilization by Combining Calcium Looping with CH4 Reforming Processes: A Thermodynamic and Exergetic Approach

Efficient Capture of CO2 from Flue Gas at High Temperature by Tunable Polyamine-Based Hybrid Ionic Liquids

Energy-efficient Process Intensification for Post-Combustion CO2 Capture: A Modeling Approach

Heat Integration, Process Design and Techno-Economic Assessment of Post-Combustion Carbon Capture Using Piperazine for Large-Scale Ethylene Plant

Simulation of H2S and CO2 Removal from IGCC Syngas by Cryogenic Distillation

Ionic Liquid-Based CO2 Capture in Power Plants for Low Carbon Emissions

Optimization of Post Combustion CO2 Capture from a Combined-Cycle Gas Turbine Power Plant via Taguchi Design of Experiment

System And Processes Of Pre-Combustion Carbon Dioxide Capture And Separation