Abstract:Li 7 La 3 Zr 2 O 12 (LLZO) garnet-type lithium-ion conductors are being investigated as a promising solid electrolyte for solid-state lithium batteries. To enable a functional all-solid-state configuration intensive investigations are needed to reduce the cathode/electrolyte interfacial resistance which contributes the most to cell performance loss. Among the commercial cathode materials investigated so far, LiCoO 2 (LCO) is one of the most stable with garnet electrolytes as only a superficial reaction has been detected between the two materials. However, even this minor reaction would block the Li-ion transport through the interface, resulting in deteriorated cell performance. In this work, we demonstrate that a thin aluminum oxide layer (5 nm) can be an effective interlayer to impede the formation of a harmful interphase and enable facile Li-ion transfer between LCO and the LLZO garnet. Room-temperature-sputtered LCO thin films were employed to form an interface with the garnet electrolyte and annealed at 800 °C to reveal the effect of the interfacial reaction on the Li-ion transfer across the interface. An aluminum oxide layer was then introduced between LCO and the garnet electrolyte by sputtering a metallic aluminum layer which is then annealed together with the upper LCO layer in oxygen, or by direct atomic layer deposition of the oxide. Compared to the LCO/LLZO/Li cells without an aluminum oxide interlayer, those with the interlayer exhibited improved performance, i.e., a stable discharge capacity of up to 90 mAh/(g LCO) at a C/10 rate, a rate capability up to 1.68C and a stable galvanostatic cycling at 0.1C for over 100 cycles with a discharge capacity fade rate of 0.15% per cycle. It was determined that aluminum diffused into the LCO layer after preventing the initial detrimental reaction between LCO and the LLZO garnet from happening during high temperature annealing, suggesting that the coating does not have to remain a physically blocking layer during cycling to function.

On-surface lithium donor reaction enables decarbonated lithium garnets and compatible interfaces within cathodes

Facile Surface Modification Method to Achieve an Ultralow Interfacial Resistance in Garnet-Based Li Metal Batteries

Molten Salt Driven Conversion Reaction Enabling Lithiophilic and Air‐Stable Garnet Surface for Solid‐State Lithium Batteries

In‐Situ Construction of Electronically Insulating and Air‐Stable Ionic Conductor Layer on Electrolyte Surface and Grain Boundary to Enable High‐Performance Garnet‐Type Solid‐State Batteries

Enhanced densification and ionic conductivity of Li-garnet electrolyte: Efficient Li2CO3 elimination and fast grain-boundary transport construction

An oxygen vacancy-rich ZnO layer on garnet electrolyte enables dendrite-free solid state lithium metal batteries

LiCoO2 Sintering Aid Towards Cathode-Interface-enhanced Garnet Electrolytes

Garnet Electrolyte with an Ultralow Interfacial Resistance for Li-Metal Batteries

Garnet Electrolyte‐Based Integrated Architecture for High‐Performance All‐Solid‐State Lithium‐Oxygen Batteries

Achieving Efficient and Stable Interface Between Metallic Lithium and Garnet-Type Solid Electrolyte Through a Thin Indium Tin Oxide Interlayer

Growth Process and Removal of Interface Contaminants for Garnet-Based Solid-State Lithium Metal Batteries

Garnet-type oxide electrolyte with novel porous-dense bilayer configuration for rechargeable all-solid-state lithium batteries

All Solid-State Li/LLZO/LCO Battery Enabled by Alumina Interfacial Coating

Artificially Transformed Ultra-Stable Li6.75La3Zr1.75Ta0.25O12 Incorporated Composite Solid Electrolyte Towards High Voltage Solid Lithium Metal Batteries

Suppressing Lithium Dendrite Growth Enabled by High-Performance Garnet LLZO for Graphite-Based Full Cell Solid-State Lithium Batteries

Restrained Li|Garnet Interface Contact Deterioration Manipulated by Lithium Modification for Solid‐State Batteries

Co-doping strategy enhanced the ionic conductivity and excellent lithium stability of garnet-type Li7La3Zr2O12 electrolyte in all solid-state lithium batteries

An in Situ-Formed LiI Interface Layer for Garnet-Based Lithium Metal Batteries

Nanosecond Laser Cleaning Method to Reduce the Surface Inert Layer and Activate the Garnet Electrolyte for a Solid-State Li Metal Battery

Optimizing Li Ion Transport in a Garnet-Type Solid Electrolyte via a Grain Boundary Design

Garnet-Based Solid Li-Metal Batteries Operable under High External Pressure with HCOOH-Induced Electron-Blocking and Lithiophilic Interlayer