Abstract:The application of Li-ion conducting garnet electrolytes is challenged by their large interfacial resistance with the metallic lithium anode and the relative small critical current density at which the lithium dendrites short-circuit the battery. Both of these challenges are closely related to the morphology and the structure of the garnet membranes. Here, we prepared four polycrystalline garnet Li6.4La3Zr1.4Ta0.6O12 (LLZTO) pellets with different particle sizes (nano/micro) and grain boundary additive (with/without Al2O3) to investigate the influence of grain size, the composition of the grain boundary, and the mechanical strength of the pellet on the total Li-ion conduction of the pellet, Li/garnet interfacial transfer, and lithium dendrite growth in all-solid-state Li-metal cells. The results showed that the garnet pellets prepared with nanoparticles and LiAlO2-related grain boundary phase had decreased total Li-ion conductivity because of the increased resistance of the grain boundary; however, these pellets showed higher mechanical strength and improved capability to suppress lithium dendrite growth at high current densities. By controlling the grain size and optimizing the grain boundary with Al2O3 sintering additive, the hot-pressing sintered LLZTO solid electrolytes can reach up to 1.01 × 10–3 S cm–1 in Li+ conductivity and 0.29 eV in activation energy. LLZTO with nanosized grain and LiAlO2-modified grain boundary showed the highest critical current density, which is 0.6 mA cm–2 at room temperature and 1.7 mA cm–2 at 60 °C. This study offers a useful guideline for preparing a high-performance LLZTO solid electrolyte.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c18674?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c18674</a>.Feature sizes of LLZTO powders prepared by hand milling and sand milling (Table S1); XRD patterns of hot-pressing sintered samples (Figure S1); element distribution on the polished surface of the sintered samples containing Al2O3 and without Al2O3 by EDX scan (Figure S2); equivalent circuit model for EIS fitting (Figure S3); and LLZTO specimens fractured by three-point bending test, gold sprayed on the surface of the micro-solid electrolyte, an optical photo of the micro-lithium symmetrical battery, and a micro-test fixture designed to test the micro-battery (Figure S4) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c18674/suppl_file/am0c18674_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

One-Step Processing of Soft Electrolyte/Metallic Lithium Interface for High-Performance Solid-State Lithium Batteries

Enhanced Performance of Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 Solid Electrolyte by the Regulation of Grain and Grain Boundary Phases

Interface Engineering for Garnet-Type Electrolyte Enables Low Interfacial Resistance in Solid-State Lithium Batteries

Achieving Efficient and Stable Interface Between Metallic Lithium and Garnet-Type Solid Electrolyte Through a Thin Indium Tin Oxide Interlayer

In‐Situ Construction of Electronically Insulating and Air‐Stable Ionic Conductor Layer on Electrolyte Surface and Grain Boundary to Enable High‐Performance Garnet‐Type Solid‐State Batteries

An in Situ-Formed LiI Interface Layer for Garnet-Based Lithium Metal Batteries

Garnet Si-Li<sub>7</sub>La<sub>3</sub>Zr<sub>2</sub>O<sub>12</sub> electrolyte with a durable, low resistance interface layer for all-solid-state lithium metal batteries

A Mortise-Tenon-like Ionic/electronic Conductive Interface Facilitates Long-Cycle Solid-State Lithium Metal Batteries

Ultrastable Anode/Electrolyte Interface in Solid-State Lithium-Metal Batteries Using LiCu x Nanowire Network Host

Ultrafast One‐Step Synthesis of Garnet‐Type Solid Electrolytes With Modified Surface and Microstructure for Solid‐State Lithium‐Metal Batteries

Garnet Li7La3Zr2O12-Based Solid-State Lithium Batteries Achieved by In Situ Thermally Polymerized Gel Polymer Electrolyte

A Facile and Low-Cost Wet-Chemistry Artificial Interface Engineering for Garnet-Based Solid-State Li Metal Batteries

Constructing a Li2O/LiZn Mixed Ionic Electron Conductive Layer by Ultrasonic Spraying to Enhance Li/Garnet Solid Electrolyte Interface Stability for Solid-State Batteries.

Mortise-tenon-like ionic/electronic conductive interface facilitates long-cycle solid-state lithium metal batteries

Asymmetrical Interface Modification Between Electrodes and Garnet-Type Electrolyte Enabling All-Solid-state Lithium Batteries

High-Performance Solid-State Lithium Metal Batteries of Garnet/Polymer Composite Thin-Film Electrolyte with Domain-Limited Ion Transport Pathways.

Interface engineering of Li6.75La3Zr1.75Ta0.25O12via in situ built LiI/ZnLix mixed buffer layer for solid-state lithium metal batteries

A Simple and Highly Efficient Method toward High-Density Garnet-Type LLZTO Solid-State Electrolyte

Enhancing interfacial stability in solid-state lithium batteries with polymer/garnet solid electrolyte and composite cathode framework

Negating Interfacial Impedance in Garnet-Based Solid-State Li Metal Batteries

In-situ construction of Li-Mg/LiF conductive layer to achieve an intimate lithium-garnet interface for all-solid-state Li metal battery