Abstract:Statement of problem: Cobalt chromium (Co-Cr) alloys possess beneficial mechanical properties because alloys, even in thin sections, can resist high mastication forces and exhibit an acceptable bond to the surface porcelain layer. Traditional manufacturing techniques of Co-Cr alloys such as casting have been replaced with newer fabrication techniques, such as milling, laser melting, and presintered milling. Despite scarce documentation, these new manufacturing techniques are being used to fabricate dental and implant constructions. Purpose: This in vitro study investigates the hardness, yield strength, elastic modulus, and microstructure of the most commonly used Co-Cr alloys for fixed prosthodontics based on manufacturing technique. In addition, this study investigates the effect of heat treatment on the mechanical properties and microstructure of these materials. Material and methods: Five Co-Cr alloys were included (dumbbell and rectangular shaped) based on four manufacturing techniques: cast, milled, laser melted, and presintered milled. Commercially pure titanium grade 4 and titanium-6 aluminum-4 vanadium ELI (extra low interstitial) were included for comparison, and yield strength and elongation after fracture were evaluated. The specimens were tested for hardness using the Vickers test and for elastic modulus using a nondestructive impulse excitation technique. The microstructure of selected specimens was analyzed using focused ion beam-scanning electron microscopy (FIB-SEM) and energy dispersive X-ray spectroscopy (EDS). Results: The mechanical properties depend on the manufacturing technique used; the laser-melted and presintered Co-Cr specimens demonstrated the highest mechanical properties, followed by the milled and cast groups. Both the laser-melted and the presintered milled Co-Cr specimens showed smaller grain size compared with the cast and milled Co-Cr specimens. The titanium-6 aluminum-4 vanadium ELI demonstrated higher hardness and yield strength compared to commercially pure titanium grade 4. No major differences were observed for the selected materials regarding the mechanical properties and microstructural appearance after heat treatment. Conclusions: The laser melting and presintered milling techniques produced higher mechanical properties compared with the cast and milled Co-Cr. These findings were confirmed through microstructural analysis with respect to the grain size, precipitation, and number of pores.

X-ray spectral microanalysis of hardened additive products made of electroerosion cobalt-chromium alloys

Microstructure and Corrosion Resistance of Medical Cobalt-Based Alloys

X-ray spectral microanalysis of W-Ni-Fe pseudoalloy obtained from electroerosive powders

Cobalt chromium alloys in fixed prosthodontics: Investigations of mechanical properties and microstructure

Microstructural Modelling Solution for Complex Co Based Alloys and Coatings

X-Ray Methods for Studying the Surface of Powder Obtained by Electroerosion Dispersion of the Waste of W–Ni–Fe 95 Pseudoalloy in Kerosene

Structure and properties of a cobalt-chromium-molybdenum alloy obtained by selective laser melting

Study on the Surface of Cobalt-Chromium Dental Alloys and Their Behavior in Oral Cavity as Cast Materials

Microstructure Evolution of FeNiCoCrAl1.3Mo0.5 High Entropy Alloy during Powder Preparation, Laser Powder Bed Fusion, and Microplasma Spraying

Hardness and Corrosion Behavior of CrMnFeCoNi Alloy Fabricated by Ball Milling and Spark Plasma Sintering

Structure and Properties of Cobalt-Based Superalloys After Electron Beam Additive Manufacturing

Additive Manufacturing of Cobalt-Based Dental Alloys: Analysis of Microstructure and Physicomechanical Properties

Synthesis of Tree-Component Cobalt-Based Alloy by Selective Laser Melting

Characterisation of heat-treated cobalt–chromium alloy fabricated by selective laser melting

Electrochemical Behavior of Cobalt-Based Nanostructured Amorphous Alloys in Alkaline Solution

Behavior of Alloying Elements in Precipitation-Hardening Hot Work Steel

Corrosion behaviors of CoCrWAlx alloys by laser additive manufacturing in molten Al

[Energy Dispersive Spectrum Analysis of Surface Compositions of Selective Laser Melting Cobalt-Chromium Alloy Fabricated by Different Processing Parameters].

Microstructure, mechanical and erosion wear analysis of post heat treated iron alloy based coating with varying chromium

THE CHROMIUM AND COBALT DISTRIBUTION IN THE DIFFUSION LAYER OF STEEL X35CrNi2-3 DURING THERMОDIFFUSION SATURATION

Chemical and Structural Analysis of Newly Prepared Co-W-Al Alloy by Aluminothermic Reaction