Abstract:Using different experimental methods, the pore radius ranges vary greatly, and most scholars use a single experiment to study pore structure, which is rarely consistent with reality. Moreover, the numerical models used in different experiments vary and cannot be directly compared. This article uniformly revised all experimental data into a cylinder model. Quantitative analysis of the full-scale pore distribution is established by mercury withdrawal–CT data, and semi-quantitative distribution is obtained by mercury–NMR–cast thin section imaging. In this paper, we introduce the tortuosity index (τ) to convert the CT ball-and-stick model into a cylinder model, and the pore shape factor (η) of the cast is used to convert the plane model into the cylinder model; the mercury withdrawal data is applied to void the influence of narrow throat cavities, and the NMR pore radius distribution is obtained using the mercury-T2 calibration method. Studies have shown that the thickness of bound water is 0.35~0.4 μm, so the pores with different radius ranges were controlled by different mechanisms in the NMR tests, with pores 10 μm were completely controlled by free relaxation. The surface relaxivity rate of fine sandstone was 18~20 μm/s. The tortuosity index τ was generally 1~7; the larger the value, the more irregular the pores. The pore shape factor η was generally 0.2~0.5; the smaller the value, the more irregular the pores. Mercury withdrawal–CT scan data can quantitatively determine the pore radius distribution curve. The coefficient of the logarithm is positive considering porosity, and the constant is negative considering porosity. Permeability controls the maximum pore radius, with a max pore radius > 100 μm and a permeability > 1 mD. Mercury withdrawal–NMR–cast thin section imaging data can semi-quantitatively establish a pore radius distribution histogram. The histogram represents quasi-normal, stepped, and unimodal data. When 60 μm is the inflection point, if a large proportion of pores measure > 60 μm, good reservoir quality is indicated. If a large proportion of pores measures < 60 μm, the permeability is generally <0.5 mD.

Three-dimensional pore characteristics and permeability properties of calcareous sand with different particle sizes

The characteristics of internal and accumulated pores of calcareous sand

Microscopic study of the impact of particle morphology on the compressibility of calcareous sands

Experimental study on the Influence of Load on Permeability Coefficient of Calcareous Sand

Micro-and macro-mechanical behavior of crushable calcareous sand in South China Sea

Study on shear characteristics of calcareous sand with different particle size distribution

Analysis Method of Full-Scale Pore Distribution Based on MICP, CT Scanning, NMR, and Cast Thin Section Imaging—A Case Study of Paleogene Sandstone in Xihu Sag, East China Sea Basin

Quantitative analysis of pore structure and permeability characteristics of sandstone using SEM and CT images

Study on pore characteristics and microstructure of sandstones with different grain sizes

Effect of Fines Content on the Compression Behavior of Calcareous Sand

Experimental Study on the Mechanical Strength, Deformation Behavior and Infiltration Characteristics of Coral Sand

Experimental investigation on mechanical behavior and particle crushing of calcareous sand retrieved from South China Sea

Effect of particle size and gradation on compressive strength of MICP-treated calcareous sand

Permeability experiment study of calcareous sand treated by microbially induced carbonate precipitation using mixing methods

Study on Effect of Particle Size Distribution on Water-Retention Capacity of Coral Sand from Macro and Micro Perspective

Particle classification and intra-particle pore structure of carbonate sands

Revisiting the liquefaction resistance of calcareous sand using X-ray CT

Effects of particle size on mechanical behaviors of calcareous sand under triaxial conditions

Multi-Scale Quantitative Characterization of Pore Distribution Networks in Tight Sandstone by Integrating FE-SEM, HPMI, and NMR with the Constrained Least Squares Algorithm

Influence of the particle morphology and internal porosity characteristics of coral sand in the South China Sea on its limit void ratio

Mechanical behavior and particle breakage of calcareous sand in triaxial test