Abstract:Using different experimental methods, the pore radius ranges vary greatly, and most scholars use a single experiment to study pore structure, which is rarely consistent with reality. Moreover, the numerical models used in different experiments vary and cannot be directly compared. This article uniformly revised all experimental data into a cylinder model. Quantitative analysis of the full-scale pore distribution is established by mercury withdrawal–CT data, and semi-quantitative distribution is obtained by mercury–NMR–cast thin section imaging. In this paper, we introduce the tortuosity index (τ) to convert the CT ball-and-stick model into a cylinder model, and the pore shape factor (η) of the cast is used to convert the plane model into the cylinder model; the mercury withdrawal data is applied to void the influence of narrow throat cavities, and the NMR pore radius distribution is obtained using the mercury-T2 calibration method. Studies have shown that the thickness of bound water is 0.35~0.4 μm, so the pores with different radius ranges were controlled by different mechanisms in the NMR tests, with pores 10 μm were completely controlled by free relaxation. The surface relaxivity rate of fine sandstone was 18~20 μm/s. The tortuosity index τ was generally 1~7; the larger the value, the more irregular the pores. The pore shape factor η was generally 0.2~0.5; the smaller the value, the more irregular the pores. Mercury withdrawal–CT scan data can quantitatively determine the pore radius distribution curve. The coefficient of the logarithm is positive considering porosity, and the constant is negative considering porosity. Permeability controls the maximum pore radius, with a max pore radius > 100 μm and a permeability > 1 mD. Mercury withdrawal–NMR–cast thin section imaging data can semi-quantitatively establish a pore radius distribution histogram. The histogram represents quasi-normal, stepped, and unimodal data. When 60 μm is the inflection point, if a large proportion of pores measure > 60 μm, good reservoir quality is indicated. If a large proportion of pores measures < 60 μm, the permeability is generally <0.5 mD.

The characteristics of internal and accumulated pores of calcareous sand

Three-dimensional pore characteristics and permeability properties of calcareous sand with different particle sizes

Micro-and macro-mechanical behavior of crushable calcareous sand in South China Sea

Microscopic study of the impact of particle morphology on the compressibility of calcareous sands

Particle shape analysis of calcareous sand based on digital images

Engineering characteristics of the calcareous sand in Nansha Islands, South China Sea

Experimental investigation on mechanical behavior and particle crushing of calcareous sand retrieved from South China Sea

Revisiting the liquefaction resistance of calcareous sand using X-ray CT

Influence of the particle morphology and internal porosity characteristics of coral sand in the South China Sea on its limit void ratio

STUDY ON CRUSHING PROCESS AND MICROSCOPIC MECHANISM OF CALCAREOUS SAND

Experimental study on the Influence of Load on Permeability Coefficient of Calcareous Sand

Mechanical behavior and particle breakage of calcareous sand in triaxial test

Particle classification and intra-particle pore structure of carbonate sands

Experimental and Mathematical Modeling of Monotonic Behavior of Calcareous Sand

Quantifying the Morphology of Calcareous Sands by Dynamic Image Analysis

Study on shear characteristics of calcareous sand with different particle size distribution

Seepage deformation characteristic of gap-graded coral sand in the South China Sea

Analysis Method of Full-Scale Pore Distribution Based on MICP, CT Scanning, NMR, and Cast Thin Section Imaging—A Case Study of Paleogene Sandstone in Xihu Sag, East China Sea Basin

Investigation on the Confined Breakage Characteristics of Calcareous Sand in the South China Sea Integrated Using Relative Breakage Ratio and Fractal Dimension

Experimental Investigation on Cementation of Calcareous Sand and Its Basic Mechanical Characteristics

Multi-Scale Quantitative Characterization of Pore Distribution Networks in Tight Sandstone by Integrating FE-SEM, HPMI, and NMR with the Constrained Least Squares Algorithm