Abstract:TC31 is a new type of α+β dual phase high temperature titanium alloy, which has a high specific strength and creep resistance at temperatures from 650 °C to 700 °C. It has become one of the competitive candidates for the skin and air inlet components of hypersonic aircraft. However, it is very difficult to obtain the best forming windows for TC31 and to form the corresponding complex thin-walled components. In this paper, high temperature tensile tests were carried out at temperatures ranging from 850 °C to 1000 °C and strain rates ranging from 0.001 s−1 to 0.1 s−1, and the microstructures before and after deformation were characterized by an optical microscope, scanning electron microscope, and electron back-scatter diffraction. The dynamic softening and hardening behaviors and the corresponding micro-mechanisms of a TC31 titanium alloy sheet within hot deformation were systematically studied. The effects of deformation temperature, strain rate, and strain on microstructure evolution were revealed. The results show that the dynamic softening and hardening of the material depended on the deformation temperature and strain rate, and changed dynamically with the strain. Obvious softening occurred during hot tensile deformation at a temperature of 850 °C and a strain rate of 0.001 s−1~0.1 s−1, which was mainly caused by void damage, deformation heat, and dynamic recrystallization. Quasi-steady flowing was observed when it was deformed at a temperature of 950 °C~1000 °C and a strain rate of 0.001 s−1~0.01 s−1 due to the relative balance between the dynamic softening and hardening. Dynamic hardening occurred slightly with a strain rate of 0.001 s−1. Mechanisms of dynamic recrystallization transformed from continuous dynamic recrystallization to discontinuous dynamic recrystallization with the increase in strain when it was deformed at a temperature of 950 °C and a strain rate of 0.01 s−1. The grain size also decreased gradually due to the dynamic recrystallization, which provided an optimal forming condition for manufacturing thin-walled components with the desired microstructure and an excellent performance.

Cold and warm flaring of thin-walled titanium tube using single-point incremental forming

Formability Enhancement in Titanium Tube-Flaring by Manipulating the Deformation Path

Hot Gas Pressure Forming of Ti-55 High Temperature Titanium Alloy Tubular Component

Process Development for a Superplastic Hot Tube Gas Forming Process of Titanium (Ti-3Al-2.5V) Hollow Profiles

Hot Gas Pressure Forming and Post Aging Treatment of Ti-22Al-24.5Nb-0.5Mo Square Tubes

Numerical and experimental analysis of the isothermal high temperature pneumoforming process

Experimental and numerical study of the flaring process for Zircaloy tube end

Thermo-Mechanical Numerical Simulation of Friction Stir Rotation-Assisted Single Point Incremental Forming of Commercially Pure Titanium Sheets

Tailoring Titanium Sheet Metal Using Laser Metal Deposition to Improve Room Temperature Single-Point Incremental Forming

Advanced FEM Insights into Pressure-Assisted Warm Single-Point Incremental Forming of Ti-6Al-4V Titanium Alloy Sheet Metal

Optimization of hot gas pressure forming process for titanium alloy component

Influence of Mandrel on the Performance of Titanium Tube with Cold Rotary Swaging

Identification of Forming Limits of CP Titanium Gr 2 Using Electrically Assisted Warm ISF Process

Effect of flow-forming parameters on surface quality, geometrical precision and mechanical properties of titanium tube

Determining the hot forming limits of titanium alloy sheet under different strain paths by constant equivalent strain rate hot gas bulging tests

Finite Element Analysis and Experimental Study of Manufacturing Thin-Walled Five-Branched AISI 304 Stainless Steel Tubes with Different Diameters Using a Hydroforming Process

Dynamic Softening and Hardening Behavior and the Micro-Mechanism of a TC31 High Temperature Titanium Alloy Sheet within Hot Deformation

Evolution of microstructure, microhardness and surface roughness of Al alloy thin-walled tube during flaring process

Formability of Thin-Walled Commercial Pure Titanium Tube upon Rotary Draw Bending

Influence of mechanical properties of tube on forming limits and deformation characteristics in expansion drawing process

Change in geometry size and thinning rate in single-point incremental forming process of TA1 sheet: evaluation method and finite element analysis