Abstract:Wire arc additive manufacturing (WAAM) technology is widely used in the fields of aerospace, shipbuilding, and automobile industry due to the advantages of fast forming speed, high material utilization and low production cost. WAAM is extremely sensitive to parameters, and different processes and materials produce different deposition effects and properties. Therefore, it is of great significance to study the WAAM formability of various materials. Herein, the microstructure, mechanical properties, and galvanic corrosion behavior of the low-carbon high-strength steel (10CrNi3MoV) fabricated by cold metal transfer (CMT) WAAM technology were investigated. The single-channel multilayer deposition parts were prepared by reciprocating deposition, and the forming parts were divided into six zones by observing the different positions of the structure: matrix, heat-affected zone, remelting zone, initial deposition zone, interlayer zone, and interlayer bonding zone. Electron backscattered diffraction (EBSD) analysis showed that the amount of recrystallization and substructure in the deposition layer had no obvious change, and the texture phenomenon was the most obvious in the initial deposition zone of the pole map reaction. The texture phenomenon gradually weakened with the increase of the deposition layers. The microhardness from the matrix to the deposition stable zone was tested. The hardness of the matrix changed smoothly, that of the heat-affected zone was the largest, and that of the deposition layer was 221–282 HV0.2. The tensile properties were tested in different directions and angles, and the yield strength and tensile strength of the deposited layer were more than 550 MPa and 760 MPa, respectively. The galvanic corrosion behavior between the deposited layer and the matrix was investigated, and the polarization curve showed that the corrosion potential of the deposited layer was lower than that of the matrix, and the corrosion current density of the deposited layer was higher than that of the matrix.

Mechanical Performance and Failure Mechanism of Layered Walls Produced by Wire Arc Additive Manufacturing in Metal Transfer Pulsed Mode

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Microstructures and Mechanical Properties of Al–Zn–Mg Aluminium Alloy Samples Produced by Wire + Arc Additive Manufacturing

Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

Characterization of 5356 Aluminum Walls Produced by Wire Arc Additive Manufacturing (WAAM)

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Printing High-Strength High-Elongation Al4043 Alloy Using UNS A94043 Welding Wires through Wire Arc Additive Manufacturing

Formability, microstructure evolution and mechanical properties of wire arc additively manufactured AZ80M magnesium alloy using gas tungsten arc welding

Microstructure, Mechanical Properties, and Galvanic Corrosion of 10CrNi3MoV Fabricated by Wire Arc Additive Manufacturing

Microstructure Evolution of Wire-Arc Additively Manufactured 2319 Aluminum Alloy with Interlayer Hammering

Microstructures and Mechanical Properties of Wire Arc Additive Manufactured 5183-Al: Influences of Deposition Dimensions

Layer-by-layer thermal modelling for wire-arc additive manufacturing of Aluminum alloy wall

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties

Wire and Arc Additive Manufacturing of High-Strength Al–Zn–Mg Aluminum Alloy

Microstructure and Mechanical Properties of Al-Cu-Mg Alloy Fabricated by Double-Wire CMT Arc Additive Manufacturing

Mechanical and microstructural features of wire-and-arc additively manufactured carbon steel thick plates

Achieving high performance of wire arc additive manufactured Mg–Y–Nd alloy assisted by interlayer friction stir processing

Mechanical Properties and Microstructural Characteristics of Al–Mg Alloy Cylindrical Component Manufactured by Wire Arc Additive Manufacturing Process

Analysis of Favorable Process Conditions for the Manufacturing of Thin-Wall Pieces of Mild Steel Obtained by Wire and Arc Additive Manufacturing (WAAM)

Periodic Microstructure of Al–Mg Alloy Fabricated by Inter-Layer Hammering Hybrid Wire Arc Additive Manufacturing: Formation Mechanism, Microstructural and Mechanical Characterization

Thermo-mechanical analysis of Wire and Arc Additive Layer Manufacturing process on large multi-layer parts