Abstract:Wire Arc Additive Manufacturing (WAAM) represents a major advancement in the production of large-scale metal components. WAAM is recognized for its capacity to produce components with enhanced material properties and structural integrity compared to conventional manufacturing processes. As WAAM involves layer-by-layer fabrication, the resulting components exhibit a higher degree of anisotropy in microstructural and mechanical properties compared to those produced by traditional methods. Additionally, the properties of WAAM components can vary significantly in terms of microstructure and mechanical performance along the build direction of the multi-layered parts. This study investigates the mechanical properties and microstructure of thin-walled cylinders made from Al-Si (Al 4043) alloy using CMT-WAAM. The analysis aims to elucidate the factors contributing to variations in these properties and provide insights into the underlying reasons for observed discrepancies. The micro hardness, tensile strength, and impact strength are analysed at both bottom and top region of the thin walled cylinder. The microhardness, tensile strength, and impact strength of the bottom region are 14.51%, 3.14%, and 12.19% less than those of the top region, respectively, due to the repeated thermal cycles during subsequent layer deposition. Fractographic analysis indicates a ductile fracture mode, characterized by the presence of dimples and microvoid coalescence. Further, the microstructural analysis reveal that top region consists fine grain compared to bottom region of thin-walled cylinder. X-ray Diffraction (XRD) analysis identified secondary phase particles, such as MgSi2 and Al9Si, at the grain boundaries, which was further confirmed by EDS analysis. These microstructural changes and the presence of secondary phases are also responsible for the changes in the mechanical properties along build direction.

Mechanical Properties and Microstructural Characteristics of Al–Mg Alloy Cylindrical Component Manufactured by Wire Arc Additive Manufacturing Process

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Mechanical properties of wire arc additive manufactured carbon steel cylindrical component made by gas metal arc welding process

Mechanical properties of wire arc additive manufactured carbon steel cylindrical component made by cold metal transferred arc welding process

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

Investigation of Microstructure and Mechanical properties of Al-Si alloy Thin Walled cylindrical part fabricated by CMT based WAAM Process

Microstructure and mechanical properties of Mg-Gd-Y-Zn-Zr alloy fabricated by cold metal transfer wire arc additive manufacturing

Wire arc additive manufacturing of a novel ATZM31 Mg alloy: Microstructure evolution and mechanical properties

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties

Arc Additively Manufactured 5356 Aluminum Alloy with Cable-Type Welding Wire: Microstructure and Mechanical Properties

Microstructure evolution and mechanical properties of Al–Cu–Mn–Cd alloy fabricated by CMT-wire arc additive manufacturing

Wire-arc additive manufacturing of AZ31 magnesium alloy fabricated by cold metal transfer heat source: Processing, microstructure, and mechanical behavior

Characterization of a low-alloy steel component produced with wire arc additive manufacturing process using metal-cored wire

Wire and Arc Additive Manufacturing of High-Strength Al–Zn–Mg Aluminum Alloy

Formability, microstructure evolution and mechanical properties of wire arc additively manufactured AZ80M magnesium alloy using gas tungsten arc welding

Microstructure and mechanical properties of wire and arc additive manufactured AZ31 magnesium alloy using cold metal transfer process

Microstructure and Mechanical Properties of Weaving Wire and Arc Additive Manufactured AZ91 Magnesium Alloy Based on Cold Metal Transfer Technique

Microstructure and Mechanical Properties of Al-Cu-Mg Alloy Fabricated by Double-Wire CMT Arc Additive Manufacturing

Printing High-Strength High-Elongation Al4043 Alloy Using UNS A94043 Welding Wires through Wire Arc Additive Manufacturing

Microstructure and Mechanical Properties of AlSi7Mg0.6 Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)