Abstract:The deposition parameters used during the sputtering process are instrumental in determining the properties of the deposited films and can be optimised to produce thin film coatings that are suitable for specific engineering applications. Deposition parameters such as radio frequency (RF) power, oxygen flow rate, and substrate temperature can be varied during deposition to alter or tune the film structure, stoichiometry, and invariably the functional properties of the prepared thin films. In this paper, chromium oxide thin films prepared by reactive magnetron sputtering under various RF powers were characterised for their work function property and stability in Ringer's solution. The structural, oxide phase and growth modes of the films were probed with X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The electrochemical stability and corrosion behaviour of the films were evaluated using an open circuit potential (OCP) measurements, cyclic polarisation, and Mott–Schottky analysis, while the work function (WF) was determined with a Kelvin probe. The XRD and Raman investigations showed that the films are predominantly amorphous with Cr 2 O 3 being the main oxide phase. A mixture of columnar and layer-by-layer growth modes was observed in the deposited films with 500 W, 10 sccm sample showing rougher morphology due to the higher sputtering power. The OCP and cyclic polarisation results showed that the film prepared at a deposition power of 300 W and at an oxygen flow rate of 10 sccm possesses higher film passivation and breakdown potentials, hence, better corrosion resistance when compared to films prepared at higher deposition powers. The finding is further supported by the Mott–Schottky and work function investigations where the same film also showed lower defect density and higher work function values compared to the films deposited at higher powers. A correlation was found between the corrosion, work function and defect density which suggests that both parameters can possibly be used to predict and rank corrosion in thin films. We expect our findings to be significant for future corrosion and wear applications for metals/alloys requiring protection against environmental degradation.

Chromium oxide films fabricated by Cr(CO)6 chemical vapor deposition

Nanoscale Ferromagnetic Chromium Oxide Film from Gas-Phase Nanocluster Deposition

CVD of CrO2 Thin Films: Influence of the Deposition Parameters on their Structural and Magnetic Properties

Study of chromium oxide film growth by chemical vapor deposition using infrared reflection absorption spectroscopy

Atomic layer deposition of chromium oxide—An interplay between deposition and etching

Preparation and Magnetic Properties of Submicron CrO2 Thin Film on Poly-Crystal TiO2 Film

Preparation and characterisation of chromium-doped cobalt oxide spinel thin films

Preparation of Chromium Oxide Coatings on Aluminum Borate Whiskers by a Hydrothermal Deposition Process

Deposition of chromium-carbon films by magnetron sputtering of chromium and carbon targets

Mechanism of Cr(III)-based Oxide-Hydroxide Film Electrodeposition in an Acidic Solution

CHARACTERIZING CRYSTALLINE CHROMIUM OXIDE THIN FILM GROWTH PARAMETERS

Observation of room temperature ferromagnetism in transition metal ions substituted p-type transparent conducting oxide Cr2O3 thin films

Preparation and Characterization of Chromium Oxide Thin Films: the Response of Morphology, Crystal Structure, and Electrical Properties to Oxygen Pressure under Magnetron Sputtering

Chromate Formed in a Trivalent Chromium Conversion Coating on Aluminum

Coercivity of γ-(Fe0.74Mn0.15Co0.11)2O3 thin films by dc reactive magnetron sputtering

Composition and Optical Properties of Chromium Oxynitride Films

Chemical Stability of Chromium Oxide Films Formed by MOCVD in Subcritical and Supercritical Water

V6O13films by Control of the Oxidation State from Aqueous Precursor to Crystalline Phase

An investigation of the work function and stability of chromium oxide thin films deposited by reactive magnetron sputtering

MAGNETITE AND MAGHEMITE THIN FILMS FOR MAGNETIC RECORDING

Plasma Assisted Pulsed Laser Deposition of WO3 Films for Thermochromism