Abstract:So far, intrinsic hydrogenated amorphous silicon (a-Si:H(i)) has been commonly used below molybdenum oxide (MoOx) to form a good contact. An a-Si:H(i)/MoOx stack gives good surface passivation, but often results in poor carrier selectivity after exposure to slightly elevated temperatures >130 °C (Geissbühler et al., 2015) [1]. For this reason, we have investigated an alternative interface layer, a very thin Al2O3 tunneling layer (<2 nm), deposited by atomic layer deposition (ALD), that can provide surface passivation, higher transparency and thermal stability without affecting the hole transport across the contact. To demonstrate this new passivating contact a 6" moly-poly cell, with an Al2O3/MoOx stack at the front side and n-type doped polysilicon at the rear side, was made using a high- throughput spatial ALD tool, and E-beam PVD, for the Al2O3 and MoOx layers, respectively. This resulted in an efficiency of 18.2% with a Voc of 651 mV, a FF of 75.6% and a Jsc of 36.9 mA/cm2. A post-deposition anneal (PDA) of the thin Al2O3 interlayer has significant effect on the Al2O3 thickness, layer stoichiometry, contact selectivity, and sputtering-induced damage. Annealing at higher TPDA (350–600 °C) results in ineffective hole carrier transport and makes the stack more sensitive to ITO damage. The best performing device was, therefore, made using an Al2O3 layer without a PDA treatment. Moreover, we have found that this solar cell structure is thermally stable up to at least 210 °C, and even slightly improves under annealing which makes this device industrially appealing.

Post-annealing Effect on Optical and Electronic Properties of Thermally Evaporated MoOX Thin Films as Hole-Selective Contacts for p-Si Solar Cells

Investigation in Feasibility of Molybdenum As A Back Contact Layer for Silicon Based Quantum Dot Solar Cells

The Effect of Thermal Annealing of Mo Film on the CuInSe2 Layer Texture and Device Performance

MoOx Hole Collection Layer for A-Si: H Based Photovoltaic Cells

Study on the Thermal Stability of Molybdenum Oxide‐Passivated Silicon Solar Cells

On The Annealing-Induced Enhancement Of The Interface Properties Of Nio:Cu/Wet-Siox/N-Si Tunnelling Junction Solar Cells

Thermally stable MoOx hole selective contact with Al2O3 interlayer for industrial size silicon solar cells

Atomic-layer-deposited H:MoOx Function Layer As Efficient Hole Selective Passivating Contact in Silicon Solar Cells

Solution-processed molybdenum oxide films by low-temperature annealing for improved silicon surface passivation

Tunable Hole Selective Transport by Solution‐processed MoO3‐x Via Doping for p‐Type Crystalline Silicon Solar Cells

Atomic-Layer-Deposited H:MoO x Function Layer as Efficient Hole Selective Passivating Contact in Silicon Solar Cells

Effect of the Post-Annealing Temperature on the Thermal-Decomposed NiOx Hole Contact Layer for Perovskite Solar Cells

Solution-processed vanadium oxide by low-temperature annealing for silicon solar cells with hole selective contact

Pre-annealing Induced Oxide Barrier to Suppress the Over-Selenization of Mo Contact

Tunable work function of molybdenum oxynitride for electron-selective contact in crystalline silicon solar cells

Sub-stochiometric MoO x by radio-frequency magnetron sputtering as hole-selective passivating contacts for silicon heterojunction solar cells

Low-temperature Solution-Processed Molybdenum Oxide Thin Film As ITO Modified Layer for Polymer Solar Cells

Chromium Trioxide Hole-Selective Heterocontacts for Silicon Solar Cells

Low Oxygen Content MoOx and SiOx Tunnel Layer Based Heterocontacts for Efficient and Stable Crystalline Silicon Solar Cells Approaching 22% Efficiency

Improved V 2 O X Passivating Contact for p ‐Type Crystalline Silicon Solar Cells by Oxygen Vacancy Modulation with a SiO X Tunnel Layer

Solution‐Processed Copper‐Doped Chromium Oxide with Tunable Oxygen Vacancy for Crystalline Silicon Solar Cells Hole‐Selective Contacts