Abstract:Titanium alloys Ti-6Al-4V are widely used in many industrial and medical applications because of their superior qualities over many other alloys like aluminum and steel. Some of their properties like high strength to weight ratio, ability to maintain strength at elevated temperatures (around 500°C) and ability of corrosion resistance in severe environmental conditions has made them excellent to use in many aerospace and bio-medical industrial applications. But the properties which make them ideal for most practical applications severely hinders their machinability and therefore, the material is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures and due to which these alloys are still machined with un-coated carbide tools at very low cutting speeds and the advantage of machining at high speed machining regime for these alloys are still not seen. The high cost of super hard cutting tools and also possible chemical reaction with work material still does not allow industrialists to use these materials for machining of titanium alloy. On the other hand recent advances in deposition of coating material on carbide tools has attracted many researchers in finding their advantages and best optimal coating combination for enhancing machinability of titanium alloys with carbide tools. This study therefore is specifically aimed and designed in evaluating the effectiveness of different coating layers on k-grade cemented carbide cutting tool by studying their effect on cutting forces, tool stresses and heat distribution by using finite element numerical simulations at high speed cutting conditions. Finite element numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Three different type of coating materials has been used in this study and the results has shown that the k-grade cemented carbide cutting tool with multi-layer coating (Al2O3+TiAlN+TiN) has shown some advantages over uncoated and single layer coating (TiAlN) in terms of heat distribution, cutting forces and tool stresses at same cutting conditions due to higher hot strength and resistance to adhesion. It can be concluded from the study that multi-layer coated k-grade cemented carbide cutting tools can be used at slightly higher speeds than un-coated or single layer coated carbide tools and can give higher tool life as compared to single layer and un- coated carbide tools.

Influence of Different Types of Cemented Carbide Blades and Coating Thickness on Structure and Properties of TiN/AlTiN and TiAlN/a-C:N Coatings Deposited by PVD Techniques for Machining of Wood-Based Materials

The influence of physical vapor deposition (PVD) coating on the microgeometry of high-speed steel (HSS) cutting tools during the machining of wood-based composites

Investigation of the Corrosion and Tribological Properties of WC-Co Tools Hardened with PVD Coatings in Solid Oak Wood Processing

Durability of cutting tools with deposited ceramic–metallic coatings (Ti,Al)N – Cu and (Ti,Al)N – Ni when turning and milling steels

Research on Tribological Characteristics of Hard Metal WC-Co Tools with TiAlN and CrN PVD Coatings for Processing Solid Oak Wood

On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys

Structural characterization and adhesion appraisal of TiN and TiCN coatings deposited by CAE-PVD technique on a new carbide composite cutting tool

Tribomechanical behavior of TiCN/TiAlN/WC-C multilayer film on cutting tool inserts for machining

The Influence of nc-AlCrTiN/α-BN Coatings on Increasing the Durability of WC/Co Cutting Inserts in the Inconel Alloy Machining Process

An Investigation of the Effect of Novel Mono/Bi-Layered PVD-Coated WC Tools on the Machinability of Ti-5Al-5V-5Mo-3Cr

Analysis of Different Complex Multilayer PACVD Coatings on Nanostructured WC-Co Cemented Carbide

Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel

Properties and Performance of TiAlSiN and AlCrN Monolayer and Multilayer Coatings for Turning Ti-6Al-4V

Evaluating the Effectiveness of Various Coating Layers Applied on K-Grade Cemented Carbide Cutting Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling

Effects of multilayer structure on impacting fatigue resistance and high-speed dry cutting performance against Ti-6Al-4 V of AlTiN/AlTiBN multilayer coatings

On the wear mechanisms of uncoated and coated carbide tools in milling titanium alloys

Microstructure and Mechanical Properties of Titanium Nitride Coatings for Cemented Carbide Cutting Tools by Pulsed High Energy Density Plasma

Enhancement of micro milling performance by abrasion-resistant coated tools with optimized thin-film thickness: analytical and experimental characterization

Comparative experimental study on application feasibiility of MTCVD TiCN-Al2O3-TiOCN multi-layer coated carbide and PVD TiN single layer coated composite ceramic inserts during dry machining of Ti-6Al-4V

Effect of Coating Thickness on the Characteristics and Dry Machining Performance of TiN Film Deposited on Cemented Carbide Inserts Using CFUBMS

Thermobarrier and antifriction properties of triboceramics on the surface of a cutting tool with (TiAlCrSiY)N/(TiAlCr)N coating during high-speed dry cutting