Abstract:Titanium alloys Ti-6Al-4V are widely used in many industrial and medical applications because of their superior qualities over many other alloys like aluminum and steel. Some of their properties like high strength to weight ratio, ability to maintain strength at elevated temperatures (around 500°C) and ability of corrosion resistance in severe environmental conditions has made them excellent to use in many aerospace and bio-medical industrial applications. But the properties which make them ideal for most practical applications severely hinders their machinability and therefore, the material is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures and due to which these alloys are still machined with un-coated carbide tools at very low cutting speeds and the advantage of machining at high speed machining regime for these alloys are still not seen. The high cost of super hard cutting tools and also possible chemical reaction with work material still does not allow industrialists to use these materials for machining of titanium alloy. On the other hand recent advances in deposition of coating material on carbide tools has attracted many researchers in finding their advantages and best optimal coating combination for enhancing machinability of titanium alloys with carbide tools. This study therefore is specifically aimed and designed in evaluating the effectiveness of different coating layers on k-grade cemented carbide cutting tool by studying their effect on cutting forces, tool stresses and heat distribution by using finite element numerical simulations at high speed cutting conditions. Finite element numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Three different type of coating materials has been used in this study and the results has shown that the k-grade cemented carbide cutting tool with multi-layer coating (Al2O3+TiAlN+TiN) has shown some advantages over uncoated and single layer coating (TiAlN) in terms of heat distribution, cutting forces and tool stresses at same cutting conditions due to higher hot strength and resistance to adhesion. It can be concluded from the study that multi-layer coated k-grade cemented carbide cutting tools can be used at slightly higher speeds than un-coated or single layer coated carbide tools and can give higher tool life as compared to single layer and un- coated carbide tools.

Tribomechanical behavior of TiCN/TiAlN/WC-C multilayer film on cutting tool inserts for machining

Thermobarrier and antifriction properties of triboceramics on the surface of a cutting tool with (TiAlCrSiY)N/(TiAlCr)N coating during high-speed dry cutting

An Investigation of the Effect of Novel Mono/Bi-Layered PVD-Coated WC Tools on the Machinability of Ti-5Al-5V-5Mo-3Cr

Properties and Performance of TiAlSiN and AlCrN Monolayer and Multilayer Coatings for Turning Ti-6Al-4V

Comparative analysis over microstructural, mechanical properties and cutting performance of TiN, TiVN coatings deposited by magnetron sputtering on SiAlON ceramic tool insert

Comparative experimental study on application feasibiility of MTCVD TiCN-Al2O3-TiOCN multi-layer coated carbide and PVD TiN single layer coated composite ceramic inserts during dry machining of Ti-6Al-4V

Mechanics and Cutting Performance of Multilayer Nanostructured TiAlN/TiSiN/ZrN Coatings

Tribological Behavior and Cutting Performance of Monolayer, Bilayer and Multilayer Diamond Coated Milling Tools in Machining of Zirconia Ceramics

Microstructure, Tribological and Cutting Performance of Ti-DLC/α-C:H Multilayer Film on Cemented Carbide

On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys

Machining performance of Ti–Al–Si–N coated inserts

Microstructure, Mechanical, Tribological, and Oxidizing Properties of AlCrSiN/AlCrVN/AlCrNbN Multilayer Coatings with Different Modulated Thicknesses

Experimental investigation of uncoated, single layer, and multilayer-coated TiAlN/TiN tool inserts in dry orthogonal cutting of AISI/SAE 4140 alloy steel

Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy

Optimizing machining efficiency: a comprehensive study on PVD cathodic arc evaporation coated turning tool inserts with TiAlN/AlCrN multilayer coatings

Effects of multilayer structure on impacting fatigue resistance and high-speed dry cutting performance against Ti-6Al-4 V of AlTiN/AlTiBN multilayer coatings

Investigation of the Properties of Ti-TiN-(Ti,Cr,Mo,Al)N Multilayered Composite Coating with Wear-Resistant Layer of Nanolayer Structure

Enhancement of micro milling performance by abrasion-resistant coated tools with optimized thin-film thickness: analytical and experimental characterization

Evaluating the Effectiveness of Various Coating Layers Applied on K-Grade Cemented Carbide Cutting Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling

Wear Resistance and Titanium Adhesion of Cathodic Arc Deposited Multi-Component Coatings for Carbide End Mills at the Trochoidal Milling of Titanium Alloy

Effect of Coating Thickness on the Characteristics and Dry Machining Performance of TiN Film Deposited on Cemented Carbide Inserts Using CFUBMS