Abstract:Titanium alloys Ti-6Al-4V are widely used in many industrial and medical applications because of their superior qualities over many other alloys like aluminum and steel. Some of their properties like high strength to weight ratio, ability to maintain strength at elevated temperatures (around 500°C) and ability of corrosion resistance in severe environmental conditions has made them excellent to use in many aerospace and bio-medical industrial applications. But the properties which make them ideal for most practical applications severely hinders their machinability and therefore, the material is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures and due to which these alloys are still machined with un-coated carbide tools at very low cutting speeds and the advantage of machining at high speed machining regime for these alloys are still not seen. The high cost of super hard cutting tools and also possible chemical reaction with work material still does not allow industrialists to use these materials for machining of titanium alloy. On the other hand recent advances in deposition of coating material on carbide tools has attracted many researchers in finding their advantages and best optimal coating combination for enhancing machinability of titanium alloys with carbide tools. This study therefore is specifically aimed and designed in evaluating the effectiveness of different coating layers on k-grade cemented carbide cutting tool by studying their effect on cutting forces, tool stresses and heat distribution by using finite element numerical simulations at high speed cutting conditions. Finite element numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Three different type of coating materials has been used in this study and the results has shown that the k-grade cemented carbide cutting tool with multi-layer coating (Al2O3+TiAlN+TiN) has shown some advantages over uncoated and single layer coating (TiAlN) in terms of heat distribution, cutting forces and tool stresses at same cutting conditions due to higher hot strength and resistance to adhesion. It can be concluded from the study that multi-layer coated k-grade cemented carbide cutting tools can be used at slightly higher speeds than un-coated or single layer coated carbide tools and can give higher tool life as compared to single layer and un- coated carbide tools.

Effect of Coating Thickness on the Characteristics and Dry Machining Performance of TiN Film Deposited on Cemented Carbide Inserts Using CFUBMS

Comparative experimental study on application feasibiility of MTCVD TiCN-Al2O3-TiOCN multi-layer coated carbide and PVD TiN single layer coated composite ceramic inserts during dry machining of Ti-6Al-4V

Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy

Tribomechanical behavior of TiCN/TiAlN/WC-C multilayer film on cutting tool inserts for machining

Evaluating the Effectiveness of Various Coating Layers Applied on K-Grade Cemented Carbide Cutting Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling

Comparative analysis over microstructural, mechanical properties and cutting performance of TiN, TiVN coatings deposited by magnetron sputtering on SiAlON ceramic tool insert

Effect of Deposition Parameters on Micromechanical Properties and Machining Performance of CrN Coating for Wet Finish Turning of Ti6Al4V Alloy

Performance analysis of novel TiN coated and uncoated carbide tool in CNC wet turning of Super Duplex Stainless steel to minimize tool wear

Experimental investigation of uncoated, single layer, and multilayer-coated TiAlN/TiN tool inserts in dry orthogonal cutting of AISI/SAE 4140 alloy steel

Hard turning of AISI H10 steel using AlTiN and AlTiSiN coated carbide tools: comparative machining performance evaluation and economic assessment

Behavior of Coated Carbide Tools in High Speed Machining of a Nickel Base Alloy

Optimizing machining efficiency: a comprehensive study on PVD cathodic arc evaporation coated turning tool inserts with TiAlN/AlCrN multilayer coatings

Measurement of roughness on hardened D-3 steel and wear of coated tool inserts

Investigations on microstructure, mechanical and tribological properties of TiN coatings deposited on three different tool materials

An Investigation of the Effect of Novel Mono/Bi-Layered PVD-Coated WC Tools on the Machinability of Ti-5Al-5V-5Mo-3Cr

Effects of TiAlN Coating Thickness on Machined Surface Roughness, Surface Residual Stresses, and Fatigue Life in Turning Inconel 718

Durability of cutting tools with deposited ceramic–metallic coatings (Ti,Al)N – Cu and (Ti,Al)N – Ni when turning and milling steels

Influence of Different Types of Cemented Carbide Blades and Coating Thickness on Structure and Properties of TiN/AlTiN and TiAlN/a-C:N Coatings Deposited by PVD Techniques for Machining of Wood-Based Materials

Wear Resistance and Titanium Adhesion of Cathodic Arc Deposited Multi-Component Coatings for Carbide End Mills at the Trochoidal Milling of Titanium Alloy

Investigation of the Wear Performance of TiB2 Coated Cutting Tools during the Machining of Ti6Al4V Alloy

Cutting performance of coated carbide inserts in hard turning of hardened AISI D2 cold work tool steels