Abstract:High-speed steel (HSS) tools account for 20 percent of the cutting tools materials' global market. This is due to both their significant toughness and resistance to cracking, compared to cemented carbides. Covering steel tools with hard coatings clearly improves their mechanical properties, wear resistance, and significantly increases their durability. Physical vapor deposition methods are preferred for coating metal substrates, as they allow low temperature deposition. The most widely deposited coating materials are carbides, nitrides, and borides. They are combined with softer ones in the multilayer structure to promote increased resistance to cracking and delamination in comparison to monolayered structures. In this paper, the M2 steel end mills were coated by (TiBx/TiSiyCz) x3 multilayer by the pulsed laser deposition method. Coated and uncoated tools were tested in the cylindrical down milling of AISI 316L steel. Components of the cutting force and temperature generated in the machined area during dry milling were measured under two variants of operating conditions: V1 and V2. Tool wear mechanism was examined using scanning electron microscopy (SEM), accompanied by EDS analysis of worn areas. It was found that milling with higher speed (variant V2) is accompanied by lower cutting force components and a lower temperature generated in cutting area. The presence of the coating allowed lower cutting forces and temperature in the case of variant V1. The temperature measured during milling did not exceed 200 °C. The SEM observation of the edges of cutting tools indicated that the main mechanism of wear for both types of tools was abrasion. The built-up edge formation was observed in the case of tools tested at the V1 cutting parameters variant. It was assumed that it was the reason for higher cutting forces measured during milling according to this variant. The chemical composition of built-up edges was different for coated and uncoated tools. Tribo-chemical reactions were responsible for the reduction of the cutting force and temperature components observed during milling with a coated tool at V1 variant. Boron and titanium were the elements of the coating that enabled the tribo-oxidation reactions thanks to which friction was reduced. Our results show that this beneficial effect occurs with (TiBx/TiSiyCz) x3 coated tools, but can easily be lost with inadequately selected cutting parameters.

The influence of physical vapor deposition (PVD) coating on the microgeometry of high-speed steel (HSS) cutting tools during the machining of wood-based composites

Influence of Different Types of Cemented Carbide Blades and Coating Thickness on Structure and Properties of TiN/AlTiN and TiAlN/a-C:N Coatings Deposited by PVD Techniques for Machining of Wood-Based Materials

Impact of Deposition of the (TiBx/TiSiyCz) x3 Multilayer on M2 HSS on the Cutting Force Components and Temperature Generated in the Machined Area during the Milling of 316L Steel

Investigation of the Corrosion and Tribological Properties of WC-Co Tools Hardened with PVD Coatings in Solid Oak Wood Processing

Research on Tribological Characteristics of Hard Metal WC-Co Tools with TiAlN and CrN PVD Coatings for Processing Solid Oak Wood

Investigation of TiCrN-Coated High Speed Steel Tools Wear during Medium Density Fiberboard Milling

Impact of coating and microstructure on wear resistance of tool steels for wood cutting: a novel approach to quantification and analysis of wear-related damages

Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Metrological analysis of changes in the surface morphology of planer knives after working surface modification

Durability of cutting tools with deposited ceramic–metallic coatings (Ti,Al)N – Cu and (Ti,Al)N – Ni when turning and milling steels

Enhancement of micro milling performance by abrasion-resistant coated tools with optimized thin-film thickness: analytical and experimental characterization

Influence of Tin Coating on Wear of High Speed Steel Tools as Studied by New Laboratory Wear Test

Performance and wear mechanisms of PCD and pcBN cutting tools during machining titanium alloy Ti6Al4V

Study and Development of a Multilayered Coating to Improve Hard Metal Cutting Tools Performances

Structural characterization and adhesion appraisal of TiN and TiCN coatings deposited by CAE-PVD technique on a new carbide composite cutting tool

Statistical Analysis of the Effect of the Cutting Tool Coating Type on Sustainable Machining Parameters

Measurement of roughness on hardened D-3 steel and wear of coated tool inserts

Enhancing Tool Performance in High-Speed End Milling of Ti-6Al-4V Alloy: The Role of AlCrN PVD Coatings and Resistance to Chipping Wear

The Influence of nc-AlCrTiN/α-BN Coatings on Increasing the Durability of WC/Co Cutting Inserts in the Inconel Alloy Machining Process

Investigation of the Wear Performance of TiB2 Coated Cutting Tools during the Machining of Ti6Al4V Alloy