Abstract:Abstract Using foams to drill in low pore pressure reservoirs is attractive because of their low density, high viscosity, and ability to transport cuttings. However, in high temperature reservoirs (240 °F) with H2S gas present, there are concerns with the long-term stability of a foam drilling fluid. In this work, we highlight a lab program to develop a stable drilling foam for drilling in a low pore pressure, high temperature reservoir. The work also includes pilot-scale experiments to evaluate foam performance. Aqueous nitrogen-in-water foams were stabilized with a preferred foaming surfactant formulation, and the rheology and stability of the foams were measured at representative drilling conditions (temperature and pressure) at the lab and pilot-scale. The foams were also evaluated for their compatibility with current drilling fluids used on site and for stability in the presence of H2S gas (at 1900 psi and 140 °F). The drilling foam was also evaluated using a pilot-scale flow loop comprised of a rheology flow loop and a model drilling wellbore. The experiments included measuring the foam rheology, foam stability in the model wellbore, and gas migration tests to understand how the foam suppresses upwardly migrating gas bubbles. We successfully developed a surfactant stabilized foam designed for a high-temperature reservoir with H2S gas present. We found that H2S can negatively impact foam stability if proper surfactants are not selected. Our foam showed less than 10% liquid drainage after 12 hours at 240 °F and showed no significant degradation upon contact with 17 mol% H2S gas. Additionally, the foam was compatible with all drilling fluids (both water-based and oil-based) currently used at the drill site and demonstrated good stability in a model pilot-scale drilling wellbore. Interestingly, when the wellbore was angled at 30 degrees from vertical with the eccentric drill pipe rotating at 100 RPM, the foams were susceptible to degradation compared to an equivalent scenario of a vertical wellbore with concentric rotating drill pipe. The gas migration tests at the pilot-scale showed the foam was capable of significantly slowing down an upwardly moving gas bubble with and without pipe rotation.

Study on the wellbore temperature distribution characteristics during foam drilling

A Unified Model To Predict Flowing Pressure and Temperature Distributions in Horizontal Wellbores for Different Energized Fracturing Fluids

Simulation study of drilling fluid cooling in long horizontal wells based on phase change heat absorption

Computational Fluid Dynamics Modeling and Analysis of Axial and Radial Temperature of Wellbore during Injection and Production Process

Study on the Flow Behavior of Underbalanced Circulative Micro-Foam Drilling Fluid

CONVECTIVE HEAT TRANSFER OF CO2 FOAM FRACTURING FLUID UNDER DOWNHOLE CONDITIONS

Sensitivity Analysis of the Parameters Affecting Bottom-hole Pressure during Foam Underbalanced Drilling

A Transient Analytical Model for Predicting Wellbore/Reservoir Temperature and Stresses during Drilling with Fluid Circulation

Study on Non-Isothermal Three-Phase Flow Characteristics in Large-Diameter Drilling Annular

Wellbore temperature and pressure calculation model for coiled tubing drilling with supercritical carbon dioxide

Study of the Heat Transfer in the Wellbore During Acid/Hydraulic Fracturing Using a Semianalytical Transient Model

Effect of the variations of thermophysical properties of drilling fluids with temperature on wellbore temperature calculation during drilling

Numerical investigation on wellbore temperature and pressure during carbon dioxide fracturing

Wellbore-heat-transfer-model-based optimization and control for cooling downhole drilling fluid

NUMERICAL INVESTIGATION OF KEY PARAMETER EFFECTS ON TEMPERATURE AND PRESSURE IN WELLBORE DURING CARBON DIOXIDE FRACTURING

Modeling the Pressure Transverse for Foam Drilling Operation in Vertical Well

A Model for Downhole Fluid and Rock Temperature Prediction During Circulation

Lab and Pilot-Scale Evaluation of Stable Foam for Drilling in High Temperature Environment

Effects of Temperature and Pressure on Rheology and Heat Transfer among Bubbles in Waterless CO2-based Foam Fracturing Fluid

Temperature Prediction of Geothermal Drilling Considering the Drilling Fluid Thermophysical Parameters

A Numerical Simulation of the Effect of Drilling Fluid Rheology on Cutting Migration in Horizontal Wells at Different Drilling Fluid Temperatures