Abstract:Abstract The use of foam is a highly attractive alternative for drilling depleted, loss circulation or gas zones. Due to its complexity, a foamed system requires special attention while designing field operations. This paper summarizes an extensive experimental program developed at PETROBRAS R&D Center facilities, coupled with a set of real scale tests under foam circulation conditions and numerical simulations, aiming the development of a comprehensive and useful model for predicting bore hole pressures while drilling under-balanced or near balance with foams. The lab work steps include foaming agent selection, rheology lab equipment development and/or adaptation, definition of test procedure and matrix, besides discussion and analysis of results. After about 60 rheology tests performed in several lab and pilot scale equipment, correlations were proposed to predict rheological parameters as functions of foam quality. Based on the experimental data, a set of correlations was developed to predict foam rheological properties as functions of base fluid rheological properties and foam quality. The next step was to evaluate the lab results by comparing pressure predictions with experimental data obtained by circulating different quality foams in a real scale vertical well located at PETROBRAS Training Center. The proper fitting of the proposed model and the experimental results supported its implementation in PETROBRAS lightweight fluid drilling software. Introduction Among the several applications of lightweight drilling fluid, one of the most attractive is the drilling of reservoirs in underbalanced or near balance conditions. This technique allows the trespassing of producing zones with minimum damage. Of course the good knowledge of hydraulics and cuttings transport mechanics of such complex systems is a must for safe and economical drilling. Nowadays, producing reservoirs in an economical way very often requires the drilling of high angle, horizontal and other more complex trajectory wells. This article presents an initial effort on experimenting and modeling flow properties of foamed systems in horizontal and inclined wells. Lab and pilot scale equipment were used as tools for the evaluation of foam stability and rheology. Based on the experiments, comprehensive curve fitting functions were proposed for explaining the flow behavior observed. Besides, a series of full scale tests with foam flowing through a closed circulation system, were performed at PETROBRAS test well. These tests aimed both the validation of the proposed model and of the procedure for working with foams in closed systems (foam generation, breaking and re-generation). This process allows the use of foam drilling technology in environments where the liquid phase can not be easily discarded, such as in offshore operations. Foam Stability - Fundamentals One important aspect for the applicability of a foaming system is the stability of the foam in downhole conditions. An important point to be investigated is the optimization of the system regarding the proper choice of the foamer agent and its optimum concentration. Foam stability is dependent on two major factors:Presence of surfactants in the liquid phase and the specific resistance of its film resulting in a bigger or smaller capacity of keeping the structure of an individual bubble.

Study on the Flow Behavior of Underbalanced Circulative Micro-Foam Drilling Fluid

Study on the wellbore temperature distribution characteristics during foam drilling

Sensitivity Analysis of the Parameters Affecting Bottom-hole Pressure during Foam Underbalanced Drilling

Foam Rheology Characterization as a Tool for Predicting Pressures While Drilling Offshore Wells in UBD Conditions

Ultra-Low-Density Drilling Fluids for Low-Pressure Coefficient Formations: Synergistic Effects of Surfactants and Hollow Glass Microspheres

Flow Characteristics of a Solid-Liquid Non-Newtonian Fluid for Directional Drilling

Study on Non-Isothermal Three-Phase Flow Characteristics in Large-Diameter Drilling Annular

Computational Fluid Dynamics Study on Bottom-Hole Multiphase Flow Fields Formed by Polycrystalline Diamond Compact Drill Bits in Foam Drilling

A Transient Analytical Model for Predicting Wellbore/Reservoir Temperature and Stresses during Drilling with Fluid Circulation

Modeling the Pressure Transverse for Foam Drilling Operation in Vertical Well

Numerical Characterization of the Annular Flow Behavior and Pressure Loss in Deepwater Drilling Riser

Experimental Investigation into an Ultra-low-Friction Water-Based Drilling Fluid for Tight Gas Well: A Case Study of Tight Gas Well in Sichuan Basin, China

APPLICATION OF PREVENTING CIRCULATION LOSS AND PLUGGING TECHNOLOGY OF THE TINY FOAM DRILLING FLUID IN WELL YUHUANG I

Research on measurement method of drilling fluid rheological parameters based on helical pipe

Design and experimental study of a new hydraulic tool for lost-circulation materials (LCM) plugging while drilling

Lab and Pilot-Scale Evaluation of Stable Foam for Drilling in High Temperature Environment

Laboratory Evaluation of Weighting Materials for Ultra-High Density Oil-Based Drilling Fluids in Ultra-HPHT Wellbore Applications

Ultra-High Density Oil-Based Drilling Fluids Laboratory Evaluation and Applications in Ultra-HPHT Reservoir

A Unified Model To Predict Flowing Pressure and Temperature Distributions in Horizontal Wellbores for Different Energized Fracturing Fluids

Factors Affecting Foam Circulation in Oil Wells

Effect of foam quality on flow behavior of liquid CO2-based foam fracturing fluid stabilized by hydrofluoroether