Abstract:Abstract Many essential parameters in hydraulic fracturing operations such as the viscosity of the fracturing fluid and the effectiveness of certain breakers, are strongly dependent on temperature. A finite-difference computer program has been developed that accurately computes temperature profiles in a propagating fracture. It is based on a rigorous description of the heat transfer processes involved:the heat influx from the fracture wall is computed numerically via a special coordinate transformation of the energy balance equation for the rock,the temperature of the frac fluid and the adjacent rock face are allowed to be different (particularly relevant for wide fractures).local time derivatives in the energy balance are fully accounted for. The code and the underlying model are valid for the full range of conditions encountered in the field, e.g.:high leak-off rates of the fracturing fluid (high permeability rock),low heal conductivity of the rock (certain carbonates) It was found that fractures are often significantly cooler than previously reported results. Consequently, the proppant carrying capacity of the frac fluid will be better and it is possible to carry out successful treatments (good proppant placement and reduced impairment) more cost-effectively. The size of prepad stages for cooling can often be reduced. Further, the temperature recovery profile after proppant placement can aid in the design of resin coated proppant systems. Introduction Many essential parameters in hydraulic fracture simulation operations are strongly dependent on the temperature level prevailing locally in the hydraulically created fracture. In fracturing treatments, the temperature affects:the viscosity of frac fluids and thereby the settling rate of the proppant.The stability of multiphase frac fluid (foams, emulsions).Crosslinker effectiveness.Viscosity breaker effectiveness.Fracture geometry (depending on the fracture propagation model assumed) These will in turn affect the ultimate productivity improvement achieved by the fracture stimulation treatment. Knowledge of the fracture temperature profile is thus requires for optimal design of the frac fluid formation (e.g. type of crosslinker) and/or the treatment stages (e.g. the size of a pre-pad sometimes required to cool the formation). The heat transfer processes taking place during a hydraulic fracture treatment are depicted in Figure q. Cold fluid is pumped into the fracture, where it cools the fracture face and the interior of the rock adjacent to the fracture by conduction and by leak-off. Simultaneously, the fluid heats up as it travels through the fracture because if conduction of heat from reservoir towards the fracture, and, in the case of acid fracturing, by the heat produced by the etching of the rock by the acid. A variety of models have been published in the open literature describing temperature profiles in the fracture for hydraulic fracturing treatments during the pumping stage(1–9), and after the pumping stage prior to closure of the fracture(10, 11) and for acid fracturing treatments(12, 13) In virtually every theory published simplifications had to be made to arrive at a workable semianalystical expression for the temperature. In this work, many restricting assumptions have been avoided. i.e.:

Study of the Heat Transfer in the Wellbore During Acid/Hydraulic Fracturing Using a Semianalytical Transient Model

Numerical simulation of fracture temperature field distribution during oil and gas reservoir hydraulic fracturing based on unsteady wellbore temperature field model

Computational Fluid Dynamics Modeling and Analysis of Axial and Radial Temperature of Wellbore during Injection and Production Process

A Transient Analytical Model for Predicting Wellbore/Reservoir Temperature and Stresses during Drilling with Fluid Circulation

A Unified Model To Predict Flowing Pressure and Temperature Distributions in Horizontal Wellbores for Different Energized Fracturing Fluids

Numerical investigation on wellbore temperature and pressure during carbon dioxide fracturing

Numerical investigation of wellbore temperature and pressure fields in CO2 fracturing

Research on Fluid–Solid Coupling Mechanism around Openhole Wellbore under Transient Seepage Conditions

A New Simulator For the Calculation of the In Situ Temperature Profile During Well Stimulation Fracturing Treatments

A Model for Downhole Fluid and Rock Temperature Prediction During Circulation

Integrated workflow of temperature transient analysis and pressure transient analysis for multistage fractured horizontal wells in tight oil reservoirs

Modeling the impact of thermal stresses induced by wellbore cooldown on the breakdown pressure and geometry of a hydraulic fracture

A New Model of Temperature Field Accounting for Acid–Rock Reaction in Acid Fracturing in Shunbei Oilfield

Transient Pressure Performance Analysis of Hydraulically Fractured Horizontal Well in Tight Oil Reservoir

Interpretation of Wellbore Temperatures Measured using Distributed Temperature Sensors during Hydraulic Fracturing

Model Calculations and Factors Affecting Wellbore Temperatures During SRV Fracturing

Analysis of Thermal Effects on Hydraulic Fracturing Near a Horizontal Well by Using Displacement Discontinuity Method

Pressure transient analysis of a vertical well with multiple etched fractures in carbonate reservoirs

Analysis of Heat Transfer Characteristics of Fractured Surrounding Rock in Deep Underground Spaces

Effect of the variation of phase-transition fracturing fluid thermophysical properties on the wellbore temperature

Combined Effects of Thermal Perturbation and In-situ Stress on Heat Transfer in Fractured Geothermal Reservoirs