Abstract:Abstract Many essential parameters in hydraulic fracturing operations such as the viscosity of the fracturing fluid and the effectiveness of certain breakers, are strongly dependent on temperature. A finite-difference computer program has been developed that accurately computes temperature profiles in a propagating fracture. It is based on a rigorous description of the heat transfer processes involved:the heat influx from the fracture wall is computed numerically via a special coordinate transformation of the energy balance equation for the rock,the temperature of the frac fluid and the adjacent rock face are allowed to be different (particularly relevant for wide fractures).local time derivatives in the energy balance are fully accounted for. The code and the underlying model are valid for the full range of conditions encountered in the field, e.g.:high leak-off rates of the fracturing fluid (high permeability rock),low heal conductivity of the rock (certain carbonates) It was found that fractures are often significantly cooler than previously reported results. Consequently, the proppant carrying capacity of the frac fluid will be better and it is possible to carry out successful treatments (good proppant placement and reduced impairment) more cost-effectively. The size of prepad stages for cooling can often be reduced. Further, the temperature recovery profile after proppant placement can aid in the design of resin coated proppant systems. Introduction Many essential parameters in hydraulic fracture simulation operations are strongly dependent on the temperature level prevailing locally in the hydraulically created fracture. In fracturing treatments, the temperature affects:the viscosity of frac fluids and thereby the settling rate of the proppant.The stability of multiphase frac fluid (foams, emulsions).Crosslinker effectiveness.Viscosity breaker effectiveness.Fracture geometry (depending on the fracture propagation model assumed) These will in turn affect the ultimate productivity improvement achieved by the fracture stimulation treatment. Knowledge of the fracture temperature profile is thus requires for optimal design of the frac fluid formation (e.g. type of crosslinker) and/or the treatment stages (e.g. the size of a pre-pad sometimes required to cool the formation). The heat transfer processes taking place during a hydraulic fracture treatment are depicted in Figure q. Cold fluid is pumped into the fracture, where it cools the fracture face and the interior of the rock adjacent to the fracture by conduction and by leak-off. Simultaneously, the fluid heats up as it travels through the fracture because if conduction of heat from reservoir towards the fracture, and, in the case of acid fracturing, by the heat produced by the etching of the rock by the acid. A variety of models have been published in the open literature describing temperature profiles in the fracture for hydraulic fracturing treatments during the pumping stage(1–9), and after the pumping stage prior to closure of the fracture(10, 11) and for acid fracturing treatments(12, 13) In virtually every theory published simplifications had to be made to arrive at a workable semianalystical expression for the temperature. In this work, many restricting assumptions have been avoided. i.e.:

Model Calculations and Factors Affecting Wellbore Temperatures During SRV Fracturing

Study of the Heat Transfer in the Wellbore During Acid/Hydraulic Fracturing Using a Semianalytical Transient Model

Numerical investigation of wellbore temperature and pressure fields in CO2 fracturing

Computational Fluid Dynamics Modeling and Analysis of Axial and Radial Temperature of Wellbore during Injection and Production Process

Numerical investigation on wellbore temperature and pressure during carbon dioxide fracturing

Calculation of Temperature in Fracture for Carbon Dioxide Fracturing

Numerical simulation of fracture temperature field distribution during oil and gas reservoir hydraulic fracturing based on unsteady wellbore temperature field model

Study on temperature distribution along wellbore of fracturing horizontal wells in oil reservoir

A New Simulator For the Calculation of the In Situ Temperature Profile During Well Stimulation Fracturing Treatments

Wellbore temperature and pressure calculation model for coiled tubing drilling with supercritical carbon dioxide

NUMERICAL INVESTIGATION OF KEY PARAMETER EFFECTS ON TEMPERATURE AND PRESSURE IN WELLBORE DURING CARBON DIOXIDE FRACTURING

Interpretation of Wellbore Temperatures Measured using Distributed Temperature Sensors during Hydraulic Fracturing

A Transient Analytical Model for Predicting Wellbore/Reservoir Temperature and Stresses during Drilling with Fluid Circulation

Effect of the variation of phase-transition fracturing fluid thermophysical properties on the wellbore temperature

Modeling the impact of thermal stresses induced by wellbore cooldown on the breakdown pressure and geometry of a hydraulic fracture

A Model for Downhole Fluid and Rock Temperature Prediction During Circulation

Thermal recovery of coalbed methane: Modeling of heat and mass transfer in wellbores

Numerical analysis of heat transfer rate and wellbore temperature distribution under different circulating modes of Reel-well drilling

Simulation of wellbore temperature and pressure field in supercritical carbon dioxide fracturing

Coupled Temperature Field Model of Gas-Hydrate Formation for Thermal Fluid Fracturing

Influences of Fracturing Fluid Injection on Mechanical Integrity of Cement Sheath under Four Failure Modes