Abstract:Microstructure characteristics are important for the high-performance Sm2Co17-type permanent magnets to achieve high intrinsic coercivity (H cj) and large magnetic field at the knee-point (H knee). In this work, the correlation between microstructures and magnetic properties has been systematically studied. The different microstructures were obtained by two procedures: by adjusting the aging temperature and optimizing the Zr content. On one hand, with increase of aging temperature from 1063 K to 1103 K, the cell size and the lamellar phase density increase from 75.1 nm and 0.014 1/nm to 101.5 nm and 0.043 1/nm, respectively, and the average peak Cu concentration at the cell boundaries reaches 21.9 at% which is helpful for obtaining relatively high H cj and H knee. As the aging temperature increases further to 1143 K, a much larger cell size and with incomplete cell boundaries results in an irregular distribution of Cu concentration at the cell boundaries. In this case, the H knee is low even though the magnet shows a high H cj. On the other hand, the increase of Zr content also promotes an increase in both the lamellar phase density and the average peak Cu concentration at the cell boundaries, giving rise to high H cj and H knee. Taking into consideration the aging temperature and Zr content, one can conclude that a lower aging temperature and lower Zr content produce a lower lamellar phase density and average Cu concentration at the cell boundaries and this leads to a lower H cj and H knee of the magnets. To further confirm this correlation between the microstructures and magnetic properties, a magnet of Sm(CobalCu0.062Fe0.285Zr0.016)7.6 was aged at a higher temperature of 1143 K to increase the lamellar phase density. As expected, the lamellar phase density increases from 0.008 to 0.013 1/nm; however, the cell size increases simultaneously from 142.5 to 247 nm. The magnet exhibits a much higher but uneven Cu concentration at the cell boundaries. As a result, the H cj increases from 1.64 to 10.18 kOe, while H knee just increases from 1.09 to 3.91 kOe.

Properties of various sintered rare earth-cobalt permanent magnets between -60° and +200°C

Sm–Co high-temperature permanent magnet materials

The physical metallurgy and processing of sintered rare earth permanent magnets

High performance 2:17 type SmCo permanent magnets with low temperature coefficients

Chemical Synthesis of Next Generation High Energy Product Hybrid SmCo Permanent Magnets for High Temperature Applications

The dependence of coercivity on anisotropy field in sintered R-Fe-B permanent magnets

Microstructural Characterization of Sm-Co Magnets

Overview of composition and technique process study on 2:17-type Sm–Co high-temperature permanent magnet

Quantitative analysis of pinning-hardened intrinsic coercivity of Sm(CoFeCuZr)z (z = 7.0–7.8) high-temperature permanent magnets

Temperature-dependent magnetocrystalline anisotropy of rare earth/transition metal permanent magnets from first principles: The light RCo$_5$ (R=Y, La-Gd) intermetallics

High-temperature dependence of anomalous Ettingshausen effect in SmCo$_5$-type permanent magnets

Design and Fabrication of Sintered Nd-Fe-B Magnets with A Low Temperature Coefficient of Intrinsic Coercivity

Recent developments in hard magnetic bulk materials

Improvement of coercivity thermal stability of sintered 2:17 SmCo permanent magnet by Nd doping

2:17-type SmCo quasi-single-crystal high temperature magnets

Microstructure, coercivity and thermal stability of nanostructured (Nd,Ce)-(Fe,Co)-B hot-compacted permanent magnets

Micromagnetics of rare-earth efficient permanent magnets

Microstructure and magnetic properties of SmCo5 sintered magnets

Temperature stability of coercivity in mischmetal-Fe-Co-B melt-spun ribbons

Realization of high-performance HRE-free Pr-Fe-B sintered magnet through microstructure regulation

Dependence of macromagnetic properties on the microstructure in high-performance Sm2Co17-type permanent magnets