Abstract:Polyimides (PI) are a class of dielectric polymer used in a wide range of electronics and electrical engineering applications from low-voltage microelectronics to high voltage isolation. They are well appreciated because of their excellent thermal, electrical, and mechanical properties, each of which need to be optimized uniquely depending on the end application. For example, for high-voltage applications, the final polymer breakdown field and dielectric properties must be optimized, both of which are dependent on the curing process and the final physico-chemical properties of PI. The majority of studies to date have focused on a limited set of properties of the polymer and have analyzed the effect of curing from a physicochemical-, mechanical- or electrical-centric viewpoint. This paper seeks to overcome this, unifying all of these characterizations in the same study to accurately describe the universal effect of the cure temperature on the properties of PI and at an industrial processing scale. This paper reports the widest-ranging study of its kind on the effect that cure temperature has on the physico-chemical, mechanical, thermal and electrical properties of polyimide, specifically poly (pyromellitic dianhydride-co-4, 4′-oxydianiline) (PMDA/ODA). The optimization of the cure temperature is accurately studied not only regarding the degree of imidization (DOI), but also considering the entire physical properties. Particularly, the analysis elucidates the key role of the charge–transfer complex (CTC) on these properties. The results show that while the thermal and mechanical properties improve with both DOI and CTC formation, the electrical properties, particularly at high field conditions, show an antagonistic behavior enhancing with increasing DOI while degrading at higher temperatures as the CTC formation increases. The electrical characterization at low field presents an enhancement of the final PI properties likely due to the DOI. On the contrary, at high electric field, the conductivity results show an improvement at an intermediate temperature emphasizing an ideal compromise between a high DOI and PI chain packing when the thermal imidization process is performed over this equilibrium. This balance enables maximum performance to be obtained for the PI film with optimized electrical properties and, overall, optimal thermal and mechanical properties are achieved.

Effects of pre-imidization on rheological behaviors of polyamic acid solution and thermal mechanical properties of polyimide film: an experiment and molecular dynamics simulation

Preparation and Dielectric Properties of Polyimide/silica Nanocomposite Films Prepared from Sol–gel and Blending Process

PREPARATION AND STUDY ON STRUCTURE OF THE POLYIMIDE/SILICA HYBRID AND NANOCOMPOSITE FILMS

Nanoporous Low‐κ Polyimide Films Via Poly(amic Acid)s with Grafted Poly(ethylene Glycol) Side Chains from a Reversible Addition–Fragmentation Chain‐Transfer‐Mediated Process

Synthesis and Properties of a High‐molecular‐weight Poly(amic Acid) and Polyimide Based on 2,2‐Bis(3‐amino‐4‐hydroxyphenyl)hexafluoropropane

Structural evolution from poly(amic acid) to polyimide fibers during thermal imidization process

Preparation and Characterization of Anisotropic Chain Structures in Polyimide Films

Viscosity-Controllable Preparation And Characterization Of Bpda-Pda Polyimide

Clarifying the effect of moisture absorption and high-temperature thermal aging on structure and properties of polyimide film at molecular dynamic level

Study on the Rheological Properties of Fluorinated Polyimide Spinning Solution

Two step synthesis of hydroxyl group polyimide based on 2,2-bis(3-amino-4-hydroxyphenyl)hexafluoropropane

Two Step Synthesis of Hydroxyl Group Polyimide Based on 2,2-Bis(amino-4-hydroxyphenyl)hexafluoropropane

Analysis of the kinetics of soluble polyimide formation by the thermal imidization of polyamic acids in amide solvents with allowance for the side reaction of anhydride group hydrolysis

A Universal Study on the Effect Thermal Imidization Has on the Physico-Chemical, Mechanical, Thermal and Electrical Properties of Polyimide for Integrated Electronics Applications

Thermal imidization of poly(amic acid) precursors on surface-modified poly(tetrafluoroethylene) films via graft copolymerization with glycidyl methacrylate

Molecular dynamics simulation and performance analysis of polyimide/aramid blends

Preparation of High-Temperature Resistant Polyimide Fibers by Introducing the p -Phenylenediamine into Kapton-Type Polyimide

Dependence of pretilt angle on orientation and conformation of side chain with different chemical structure in polyimide film surface

Effect of amine and acid functionalization on polyimide: A structure-property relationship study

Preparation of Meldrum's Acid‐functionalized Polyimides Exhibiting Organo‐soluble, Reactive, Self‐crosslinkable, and Colorless Features

Structure and Properties of Thermoplastic Polyimide Based on 4', 4'-(Oxybis (methylene)) Bis ([1.1'- Bipheny]3-Amine) Diamine