Abstract:Introduction Large-scale water electrolysis is needed for scaling up the production of hydrogen as a renewable energy carrier. The required size and number of cells of the PEMWE stack exceed laboratory-scale settings, which leads to additional effects that could impact the operation and performance [1]. The interaction of large, neighbouring cells with each other are expected to lead to significant temperature differences within the stack of cells, which cause deviations in the contribution to the loss mechanisms and uneven stresses or loading of the members. Methods This contribution presents a dynamic PEMWE-stack model, which is formulated in two dimensions: through the stack and along the channel. Due to the high electric conductivity of the bipolar plates the cell voltage of each cell is independent of the cell/channel flow coordinate. The model is based on mass and enthalpy balances of the fluids on the anodic and cathodic side. Conductive heat transport along the cell and through the stack is considered as well as convective transport by the fluids. Time-dependency of mass and enthalpy balances is considered to capture unsteady operation of the stack. In addition, a temperature-dependent polarisation model for determining the cell voltage is included in the model. The polarisation model includes the contributions of activation overpotentials, mass transport losses and ionic membrane and contact resistances. The cells on both edges of the stack are modelled with dedicated boundary conditions to capture the physical arrangement and convective heat exchange with the environment. Water flow and electrical settings are prescribed as external boundary condition. The model is validated with experimental data from industrial stacks. Results The temperature profile inside the stack is found unevenly distributed in both spatial directions between the cells with colder boundary and warmer inner cells. The colder outer cells operate at a higher cell voltage in an electrical series connection. For the inner cells, a significant temperature gradient is found in flow direction. As the polarisation loss mechanisms depend on temperature, the share of the losses is unevenly distributed in both coordinates. This leads to higher current densities at the parts of a cell that experience elevated temperatures (Fig. 1). These mechanisms depend on the macroscopic design of the cell, boundary and operating conditions. Load variations induce a dynamic stack response in temperature, cell voltage and the fluids until a steady state is reached. At the same time local temperature and current density variation, can be analyzed as performance drivers, including degradation. Both aspects can be used for design and optimization of industrial scale PEMWE stacks. References [1] S. Siracusano, V. Baglio, N. Briguglio, G. Brunaccini, A. Di Blasi, A. Stassi, R. Ornelas, E. Trifoni, V. Antonucci and A. S. Aricò, International Journal of Hydrogen Energy, 37(2), 1939–1946 (2012). Figure 1

Semiempirical Model for Determining PEM Electrolyzer Stack Characteristics

Electrochemical Performance Modeling of A Proton Exchange Membrane Electrolyzer Cell for Hydrogen Energy

Modeling of Two-Phase Transport in Proton Exchange Membrane Electrolyzer Cells for Hydrogen Energy

Experimental Validation of an Equivalent Dynamic Electrical Model for a Proton Exchange Membrane Electrolyzer

A single-phase, non-isothermal model for PEM fuel cells

Temperature and Performance Inhomogeneities in PEM Electrolysis Stacks with Industrial Scale Cells

Effects of Membrane Electrode Assembly Properties on Two-Phase Transport and Performance in Proton Exchange Membrane Electrolyzer Cells

A model predicting performance of proton exchange membrane fuel cell stack thermal systems

A comprehensive study of parameters distribution in a short PEM water electrolyzer stack utilizing a full-scale multi-physics model

Proton Exchange Membrane Electrolyzer Systems Operating Dynamically at High Current Densities

Quantifying Temperature Effects in Large-Scale PEM Water Electrolysis Stacks

Performance of Polymer Electrolyte Membrane Water Electrolysis Systems: Configuration, Stack Materials, Turndown and Efficiency

Cell voltage static-dynamic modeling of a PEM electrolyzer based on adaptive parameters: Development and experimental validation

Assessing the Performance of a Proton Exchange Membrane Green Hydrogen Generation System through Stack and Balance of Plant Modeling

Anion exchange membrane water electrolysis: Numerical modeling and electrochemical performance analysis

Simulation and experiment study on two-phase flow characteristics of proton exchange membrane electrolysis cell

Aspects of Reduced Performance of Proton-Exchange-Membrane Water Electrolysis Via Continuum Modeling

Three-Dimensional Numerical Simulation of the Performance and Transport Phenomena of Oxygen Evolution Reactions in a Proton Exchange Membrane Water Electrolyzer

Operando analysis of in-plane heterogeneity for the PEM electrolyzer cell: Mappings of temperature and current density

Membrane electrode assembly simulation of anion exchange membrane water electrolysis

Numerical Investigation on the Effects of Design Parameters and Operating Conditions on the Electrochemical Performance of Proton Exchange Membrane Water Electrolysis