Abstract:The Hydrogen production plays important role as part of energy transition strategy in Germany as well as in visions and subsequent policy of European Green Deal activities. Schaeffler [1] is driving further technological development with strong financial backing of European (CHP) and German funding (H2Giga). PEM water electrolysis is regarded as powerful technology, bringing advantages of limited installation footprint, broad range of operating conditions, especially in terms of dynamic load range and featuring high efficiency between 75-90% (based on HHV) [2]. Minimizing the Levelized Cost of Hydrogen demands reduction in CAPEX, OPEX, maintenance whilst extending lifetime to secure full Return of Investment [3]. In addition, production of green hydrogen needs to anticipate the intermittent and distributed nature of renewable energy sources whilst functioning in a decentralized energy distribution network. Enabling maximum uptime sets high demands on the stack performance requirements and its material specifications. Here we show examples of how component development and design iterations make a huge impact on the commercial viability of electrolysers in industrial applications. Efficiency is key when converting renewable electricity and water into green hydrogen and other chemicals, even though PEM electrolyser stack technology is deemed capable of increasing current densities up to 10 A/cm 2 . Therefore, State-of-Art commercial stacks are rated at current densities between ~1-3 A/cm 2 , but this anticipated trend to increase power density underlines the necessity to reduce the total electrical resistance and avoid Ohm’s losses. Critical to success is selecting materials that can sustain functionality, stability and compatibility within an operational window being pushed to higher current density to increase stack output, whilst reducing PGM content and overall cost. Progress has been achieved by combining formed metal components with durable, conductive coatings, and establishing optimum compression. Most promising results published in open literature are based on small cells on laboratory scale (5-25 cm 2 active area). So-called “screeners” are ideally suited for studying phenomena under well-controlled conditions with a plethora of diagnostic tools. In contrast, large-area stacks operated in the field don’t always operate under ideal operating conditions and can show variability in performance characteristics that escalate into unexpected degradation issues. Of course, stack behavior is dependent on its local environment within the BOP system, relative to its peers. We show how continuous remote monitoring during operation helps identify non-uniform stack operation and flag off-spec conditions, which could form the basis of Accelerated Stress Tests for testing in the laboratory. In this work we estimate how much stack technology can be improved further by forming BPP metal structures and optimizing the component design using CFD. Especially when scaling stack hardware to larger capacity, there is much emphasis on enhanced thermal management to avoid hot-spots and mitigate non-uniform degradation mechanisms and premature stack failure. Simulation results will show how flow designs could be adapted maintain uniform conditions when scaling up the active area or adding more cells to the stack. Robust Stacks are demanded for market ramp-up, demonstrating predictable performance over a long lifetime and insensitivity to a wide range of possible operating conditions. However, but to the best of our knowledge, no component- nor stack- supplier is willing to provide extensive guarantees. Fortunately, stacks quality can be improved significantly by strong automotive and manufacturing industries stepping into the PEM electrolyzer arena and introducing their automated assembly, mature manufacturing and controlled processes to guarantee reproducibility, tight tolerances, superior quality and support supply chain development. Before ramping up global production capacity massively, all players would benefit from standardizing general geometric specifications of stacks so we can leverage a stronger collective learning curve with increasing numbers. References [1] K. Rosenfeld, The Stern Stewart Institute, periodical #27 (2023) 20-27. [2] Y. Wang et.al., Energy Environ. Sci., 15 (2022) 2288-2328. [3] P. Lyubarskyy, interview: Imagining a Hydrogen-Powered Future Thanks to Simulation (2023). [4] J. Proost, Int. J. of Hydrogen Energy 44 (2019), 4406 – 4413. Figure 1

Temperature and Performance Inhomogeneities in PEM Electrolysis Stacks with Industrial Scale Cells

Quantifying Temperature Effects in Large-Scale PEM Water Electrolysis Stacks

Operando analysis of in-plane heterogeneity for the PEM electrolyzer cell: Mappings of temperature and current density

A single-phase, non-isothermal model for PEM fuel cells

A comprehensive study of parameters distribution in a short PEM water electrolyzer stack utilizing a full-scale multi-physics model

Study on the Heat and Mass Transfer Mechanisms of Liquid-Cooled PEMFC Stacks Based on Non-Isothermal Model

Electrochemical Performance Modeling of A Proton Exchange Membrane Electrolyzer Cell for Hydrogen Energy

Full-scale three-dimensional simulation of air-cooled proton exchange membrane fuel cell stack: Temperature spatial variation and comprehensive validation

A comprehensive investigation on performance heterogeneity of commercial-size fuel cell stacks during dynamics operation

Experimental study of the thermal and power performances of a proton exchange membrane fuel cell stack affected by the coolant temperature

Performance of Polymer Electrolyte Membrane Water Electrolysis Systems: Configuration, Stack Materials, Turndown and Efficiency

3D multi-phase simulation of metal bipolar plate proton exchange membrane fuel cell stack with cooling flow field

Numerical investigations on electrolytic performance of proton exchange membrane electrolysis cell with parallel flow field

A Segmented Along the Channel Test Cell for Locally Resolved Analysis at High Current Densities in PEM Water Electrolysis

Full-scale three-dimensional simulation of air cooling metal bipolar plate proton exchange membrane fuel cell stack considering a non-isothermal multiphase model

Investigation of non-uniform temperature distribution in air-cooled proton exchange membrane fuel cells with multizone temperature measurement

Novel electrochemical and thermodynamic conditioning approaches and their evaluation for open cathode PEM-FC stacks

Investigation of the Ambient Temperature Influence on the PEMFC Characteristics: Modeling from a Single Cell to a Stack

Influence of Anode Flow-Field Channel Distance on the Performance of Polymer Electrolyte Membrane Water Electrolyzers

Thermal characteristics of an air‐cooled open‐cathode proton exchange membrane fuel cell stack via numerical investigation

(Invited) Industrialization of PEM Electrolyzer Stack Platforms: Driving Lab-Scale Innovation to Multi-MW Implementation