Abstract:<p>The size, distribution and chemical composition of grain boundary η-phase precipitates (GBPs) and micro-segregation present in thick plate (140 mm) 7xxx Al alloys has been quantified across a range of length scales. To address the known limitations of individual characterisation methods, a number of cross-correlated, high resolution techniques have been used, including atom probe tomography (APT). A new-generation high-Zn alloy (AA7085) has been compared to a more established material, AA7050, in T7651 temper conditions. The results show that high angle grain boundaries in both alloys are dominated by quench-induced GBPs (Q-GBPs), covering up to ∼40% of the area in AA7050. When viewed on brittle intergranular fracture surfaces and in 3D, the Q-GBPs appear much larger than previously reported and exhibit complex branched-facetted morphologies. In AA7050, the Q-GBPs contain substantially higher levels of Cu (by 29 %) and Al (by 37%) and lower Zn (by 33 %) than AA7085. Classical modelling demonstrates that these differences result from different transformation pathways, with precipitates in the more quench sensitive AA7050 alloy nucleating at higher temperatures, which exaggerates the effect of alloy chemistry. In both alloys GB segregation was limited, with low levels of Zn detected relative to the matrix, but more Mg and less Cu in AA7050. It is, therefore, proposed that the higher Cu and Al, and lower Zn content, of the large Q-GBPs present in AA7050 is the main difference in GB microchemistry between the two materials and is the primary reason its GBs are less chemically active. The implications for the relative susceptibilities of the alloys to environmentally assisted cracking are briefly discussed.</p>

Structural and crystallographic characterization of grain boundaries coarse particles in an Al–Mg–Si alloy, using convergent beam electron diffraction

High-Resolution Electron Microscope Observation of Interface Microstructure of A Cast Al-Mg-Si-Bi-Pb(6262)/Al2o3p Composite

Interfacial Segregation and Precipitates Behavior in the Ultrafine Grained Al-based Metal Matrix Composites

Grain boundary decohesion in body-centered cubic Mg-Li-Al alloys

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

Grain boundary character distribution in the CoCrMo alloy processed by selective laser melting and post-heat treatment

Multiscale analysis of grain boundary microstructure in high strength 7xxx Al alloys

Grain boundary segregation spectrum in basal-textured Mg alloys: From solute decoration to structural transition

Towards Homogeneous Distribution of Coarse Grain in a Tri-Modal Al-based Composites Utilizing Localized Grain Growth

Grain boundary segregation in UFG alloys processed by severe plastic deformation

Transmission Electron Microscopy Study of the Early-Stage Precipitates in Al-Mg-Si Alloys

First-principles investigation of the Mg, Cu segregation at Al Σ5 (310) and Σ9 (221) symmetrical tilt grain boundaries

Evolution of Deformation Substructure and MgxZnyCaz Metastable Phase in Fine-Grained Mg Alloys

Grain growth competition and formation of grain boundaries during solidification of hcp alloys

3D Characterization of a Nanostructured Al-Cu-Mg Alloy

Atomistic Study of Grain-Boundary Segregation and Grain-Boundary Diffusion in Al-Mg Alloys

Influence of variation in grain boundary parameters on the evolution of atomic structure and properties of [111] tilt boundaries in Aluminum

Effects of KoBo-Processing and Subsequent Annealing Treatment on Grain Boundary Network and Texture Development in Laser Powder Bed Fusion (LPBF) AlSi10Mg Alloy

High-resolution transmission electron microscopy and tomographic atom probe studies of the hardening precipitation in an Al–Cu–Mg alloy

Periodic linear complexions: Co-segregation of solutes at a low-angle grain boundary in a magnesium alloy