Abstract:Twin-screw granulation is a promising wet granulation technique for the continuous manufacturing of pharmaceutical solid dosage forms. A twin screw granulator displays a short residence time. Thus, the solid-liquid mixing must be achieved quickly by appropriate arrangement of transport and kneading elements in the granulator screw allowing the production of granules with a size distribution appropriate for tableting. The distribution of residence time and granulation liquid is governed by the field conditions (such as location and length of mixing zones) in the twin-screw granulator, thus contain interesting information on granulation time, mixing and resulting sub-processes such as wetting, aggregation and breakage. In this study, the impact of process (feed rate, screw speed and liquid-to-solid ratio) and equipment parameters (number of kneading discs and stagger angle) on the residence time (distribution), the granulation liquid-powder mixing and the resulting granule size distributions during twin-screw granulation were investigated. Residence time and axial mixing data was extracted from tracer maps and the solid-liquid mixing was quantified from moisture maps, obtained by monitoring the granules at the granulator outlet using near infra-red chemical imaging (NIR-CI). The granule size distribution was measured using the sieving method. An increasing screw speed dominantly reduced the mean residence time. Interaction of material throughput with the screw speed and with the number of kneading discs led to most variation in the studied responses including residence time and mixing capacity. At a high screw speed, granulation yield improved due to high axial mixing. However, increasing material throughput quickly lowers the yield due to insufficient mixing of liquid and powder. Moreover, increasing liquid-to-solid ratio resulted in more oversized granules, and the fraction of oversized granules further increased at higher throughput. Although an increasing number of kneading discs was found to be critical for achieving a uniform distribution of the granulation liquid, the granulation performance was hampered due to insufficient solid-liquid mixing capacity of the current kneading discs which is essential for wet granulation. Thus, a balance between material throughput and screw speed should be strived for in order to achieve a specific granulation time and solid-liquid mixing for high granulation yield. Additionally, more efforts are needed both in modification of the screw configuration as well as the geometry of the mixing elements to improve the mixing capacity of the twin-screw granulator. The results from the current experimental study improved the understanding regarding the interplay between granulation time and the axial and solid-liquid mixing responsible for the granulation performance in twin-screw wet granulation.

Effect of Impeller and Chopper Design on Granulation in a High Speed Mixer

Effect of Agitation on the Fluidization Behavior of a Gas–solid Fluidized Bed with a Frame Impeller

Nanoparticle Deagglomeration Driven by a High Shear Mixer and Intensification of Low-Speed Stirring in a Viscous System

Numerical investigation of mixing and heat transfer of granular material in a ribbon reactor: effect of impeller speed and filling rate

Investigation of mixing homogeneity of binary particle systems in high-shear wet granulator by DEM

Continuous wet granulation using fluidized-bed techniques I. Examination of powder mixing kinetics and preliminary granulation experiments

Investigation the iron ore fine granulation effects and particle adhesion behavior in a horizontal high-shear granulator

An Understanding of the Relationship Between Mixing Performance and Power Consumption in a High-Shear Wet Granulation Pre-mixing

Analysis of End-Point with Power Consumption in High Speed Mixer

Pre-nucleation in high-shear wet granulation

Development of tapered rotating fluidized bed granulator for increasing yield of granules

Investigation on the granulation behavior of iron ore fine in a horizontal high-shear granulator

DEM simulation OF A single SCREW GRANULATOR: THE EFFECT OF LIQUID BINDER ON GRANULE PROPERTIES

Influence of the centrifugal granulating process on the properties of layered pellets

Experimental investigation of heat generation during the mixing of granular materials using an overhead stirrer

Effects of Geometric Parameters and Operating Conditions on Granular Flow in A Modified Rotating Cone

The effect of impeller configurations on particle mixing in an agitated paddle mixer

Mechanistic understanding of the effects of process and design parameters on the mixing dynamics in continuous twin-screw granulation

Linking granulation performance with residence time and granulation liquid distributions in twin-screw granulation: An experimental investigation

In Silico CFD Investigation of the Granulation Hydrodynamics in Rotating Drum: Process Sensitivity to the Operating Parameters and Drag Models

Granulation of Lactose in a Recording High-Speed Mixer, Diosna P25