Abstract:Twin-screw granulation is a promising wet granulation technique for the continuous manufacturing of pharmaceutical solid dosage forms. A twin screw granulator displays a short residence time. Thus, the solid-liquid mixing must be achieved quickly by appropriate arrangement of transport and kneading elements in the granulator screw allowing the production of granules with a size distribution appropriate for tableting. The distribution of residence time and granulation liquid is governed by the field conditions (such as location and length of mixing zones) in the twin-screw granulator, thus contain interesting information on granulation time, mixing and resulting sub-processes such as wetting, aggregation and breakage. In this study, the impact of process (feed rate, screw speed and liquid-to-solid ratio) and equipment parameters (number of kneading discs and stagger angle) on the residence time (distribution), the granulation liquid-powder mixing and the resulting granule size distributions during twin-screw granulation were investigated. Residence time and axial mixing data was extracted from tracer maps and the solid-liquid mixing was quantified from moisture maps, obtained by monitoring the granules at the granulator outlet using near infra-red chemical imaging (NIR-CI). The granule size distribution was measured using the sieving method. An increasing screw speed dominantly reduced the mean residence time. Interaction of material throughput with the screw speed and with the number of kneading discs led to most variation in the studied responses including residence time and mixing capacity. At a high screw speed, granulation yield improved due to high axial mixing. However, increasing material throughput quickly lowers the yield due to insufficient mixing of liquid and powder. Moreover, increasing liquid-to-solid ratio resulted in more oversized granules, and the fraction of oversized granules further increased at higher throughput. Although an increasing number of kneading discs was found to be critical for achieving a uniform distribution of the granulation liquid, the granulation performance was hampered due to insufficient solid-liquid mixing capacity of the current kneading discs which is essential for wet granulation. Thus, a balance between material throughput and screw speed should be strived for in order to achieve a specific granulation time and solid-liquid mixing for high granulation yield. Additionally, more efforts are needed both in modification of the screw configuration as well as the geometry of the mixing elements to improve the mixing capacity of the twin-screw granulator. The results from the current experimental study improved the understanding regarding the interplay between granulation time and the axial and solid-liquid mixing responsible for the granulation performance in twin-screw wet granulation.

Pre-nucleation in high-shear wet granulation

Nucleation, growth and breakage phenomena in agitated wet granulation processes: a review

Powder wetting behavior and granule formation mechanism expansion in single-drop granulation

Nucleation regime map for liquid bound granules

Dynamic Densification of Wet Granular Materials in Continuous Dense Flows under Gravity

Linking granulation performance with residence time and granulation liquid distributions in twin-screw granulation: An experimental investigation

Application of Near-Infrared Spectroscopy Combined with Design of Experiments for Process Development of the Pulsed Spray Fluid Bed Granulation Process

An Understanding of the Relationship Between Mixing Performance and Power Consumption in a High-Shear Wet Granulation Pre-mixing

Model-based analysis of high shear wet granulation from batch to continuous processes in pharmaceutical production--a critical review

Particle dynamics simulation of wet granulation in a rotating drum

Investigation of mixing homogeneity of binary particle systems in high-shear wet granulator by DEM

Granulation Rheology I: Equipment Design and Preliminary Testing

Continuous wet granulation using fluidized-bed techniques I. Examination of powder mixing kinetics and preliminary granulation experiments

Mechanistic understanding of the effects of process and design parameters on the mixing dynamics in continuous twin-screw granulation

An Evaluation of Process Variables in wet Granulation

Twin screw wet granulation: Loss in weight feeding of a poorly flowing active pharmaceutical ingredient

Elucidation of granulation mechanisms along the length of the barrel in continuous twin-screw melt granulation

Investigating the Effects of Mixing Dynamics on Twin-Screw Granule Quality Attributes via the Development of a Physics-Based Process Map

Effect of Impeller and Chopper Design on Granulation in a High Speed Mixer

Analysis of the Effects of Process Parameters on Start-Up Operation in Continuous Wet Granulation

Influence of separation properties and processing strategies on product characteristics in continuous fluidized bed spray granulation